CTC Union FRM220A-GSW/SNMP User Manual Download Page 9

Page: 9 / 52

Chapter 1 Introduction

1.6 Chassis Specifications

Environment

Temperature

-10 - 50

C (14-122

Humidity

5-95% non condensing

Alarm relay contact ratings

125VAC 1A
110VDC 0.6A
30VDC

Power Module Specifications

AC Power Module

Input : Universal, 100~240VAC ±10% at ambient temperature; Frequency : 47~63 Hz

Output : DC 12V, 200W maximum rating (Green power rated, 89% power efficiency)

Connector : C14 (IEC 60320-1)

DC Power Module

Input : -36~75 VDC (option 1)

Input : -18~-36VDC (option 2)

Output : DC 12V, 200W maximum rating

Connector : 3 connector terminal block

AC Power Cord Specification

(detachable cord, C13 connector, with national plug per national standards)

6A rated 18AWG (conductors with a minimum cross-section area of 0.75 mm

)

DC Power Cord Specification

(wiring must comply with EN 60950-1:2006 standard)

Conductors with a minimum cross-section area of 1mm

(16AWG)

Power Consumption

~120 watts (fully loaded chassis, with random mix of line card types)

Heat Generation

~280 BTU (fully loaded chassis, with random mix of line card types)

Compliance

European Union : EN55022:2006, Class A, EN55024:1998+A1:2001+A2:2003, and EN60950-1:2006

FCC : part 15, subpart B, class A

Reliability

MTTB : >65,000 hours (25

Physical Specifications

Dimensions : 438mm (Width) x 302mm (Depth) x 88mm (Height)

(US: 17 1/4" wide x 11 7/8" deep x 3 1/2" high)

Weight : 4.5Kg (US: ~10 lbs)

AC module weight : 690g (US 1.5 lbs)

DC module weight : 505g (US 1.2 lbs)

Fan module weight : 200g (US 0.5 lbs)

GSW/SNMP card weight : 200g (US 0.25 lbs)

Net Weight : 7.0kgs (US 15 lbs 8 oz)

(with 1 GSW/SNMP, 2 fan modules, 1 AC +1 DC power module & two bracket panels for 19" rack-

mounting)

Fully Populated Reference Net Weight: 8.7Kg (US 19.2 lbs.)

(fully loaded, two powers, GSW/SNMP and 20 pcs 5E/ET100 line cards)

Summary of Contents for FRM220A-GSW/SNMP





















































Search results

Summary of Contents for FRM220A-GSW/SNMP

Reviews:

Brands by name

Popular brands

CTC Union FRM220A-GSW/SNMP, User Manual

Search results

Summary of Contents for FRM220A-GSW/SNMP

Reviews:

Brands by name

Popular brands