CTC Union ecoflex, Installation And Maintenance Manual

Page: 19 / 60

19
CTC EcoFlex
End user information
Night reduction No
Here you can select whether you want to activate night time temperature
lowering (lower room temperature at night). Two periods of lower
temperatures per day, seven days a week can be programmed. Lowering
can also be programmed for blocks of days.
Installer This menu contains two sub menus. One menu is used to set all basic
settings and one menu is used by service personnel.
Settings
►
Lang. English
Heat pump No
Indoor sens No
Boiler pellet °C 80
Alarm FlueGas °C 240
El Boiler °C 50
El boiler max kW 6,0
Max fuse A 20
External control NR
Setting house Param
Setting pellet
Holiday off
Set. tank
Setting DHW
Save setting
Load setting
Load factory setting
Service
►
Functiontest pellets
Funktionstest other
Alarm info
Functiontest pellet
►
Auger Feeder Off
Fan % 0
Auger burner % 0
El ignition Off
Funct. test other
►
ElRelay 1,5/3 kW 0
ElRelay 3/6 kW 0
Pellet Off
Heatingcirpump.
Off
MixingValve Close
DHW pump
Off
Diode sensor Off
Alarm stored
Last alarm
xxxxx
Stored alarm
xxxxx
xxxxx
xxxxx
xxxxx
Setting Heating
►
Max Primfl °C 55
Min Primfl °C Off
Heating off 16
Heat curve
Inclination 50
Adjustment 0
Setting pellet
►
Level sensor % 0(50)
Flame detector % 99(50)
Burner type kW 15
Power full auger % 68
Power full fan % 40
Power part auger % 41
Power part fan % 20
Power min auger % 0
Power min fan % 0
Holding min 60
Auger Feeder s 30
Sequenz code 0
Time setting
Day
Thursday
Time 18:03
Stored oper data
Total operation h
8768
El heat kWh 1234
Pellet h 3456
Max prim °C 62
Cold starts 14
Warm starts 354
Night reduction
►
Activated No/Yes
Type WeekProg
Indoor temp red °C
-2
Prim red °C -5
WeekProgram
Installer
►
Settings
Service
Operation data
Outdoor °C
-5
Indoor °C 20(20)
Boiler °C 70
FlueGas °C 160
Primfl . °C 45(45)
▼
Operation data
▲
Current A 12(20)
Pellet startphase 1K
Mixingvalve close
Program ID xxxxxxx
Program date xx-xx-xx
Operation data
▲
Heatingcirc. pump On
Elpower 3,0
▼
With indoor sensor
Without indoor sensor
With indoor sensor
Without indoor sensor
EcoFlex Thurs 8:03
Indoor °C 20.0(20.0)
Indoor Temp NR
Boiler °C 50
►
Operation data
Stored oper data
Night reduction
Installer
Indoor temp
-
● ● ● ●
+ (52)
Set. tank
►
Charge tank Yes
Temp tank °C 70
Diff °C 5
Tank prio No
3.3 Menu Time setting
(at the top of the normal display menu)
Day and time can be set here. The clock is metered by the mains electricity
network frequency (50 Hz). If there is a power cut, reset the clock. The
clock restarts at the time immediately before the power cut ± 5 minutes.
Summer time/winter time is set manually.
Day Mon Set current day (Monday...Sunday).
Time 00:00 Set current time (00:00… 11:59 pm)
Settings
►
Lang. English
Heat pump No
Indoor sens No
Boiler pellet °C 80
Alarm FlueGas °C 240
El Boiler °C 50
El boiler max kW 6,0
Max fuse A 20
External control NR
Setting house Param
Setting pellet
Holiday off
Set. tank
Setting DHW
Save setting
Load setting
Load factory setting
Service
►
Functiontest pellets
Funktionstest other
Alarm info
Functiontest pellet
►
Auger Feeder Off
Fan % 0
Auger burner % 0
El ignition Off
Funct. test other
►
ElRelay 1,5/3 kW 0
ElRelay 3/6 kW 0
Pellet Off
Heatingcirpump.
Off
MixingValve Close
DHW pump
Off
Diode sensor Off
Alarm stored
Last alarm
xxxxx
Stored alarm
xxxxx
xxxxx
xxxxx
xxxxx
Setting Heating
►
Max Primfl °C 55
Min Primfl °C Off
Heating off 16
Heat curve
Inclination 50
Adjustment 0
Setting pellet
►
Level sensor % 0(50)
Flame detector % 99(50)
Burner type kW 15
Power full auger % 68
Power full fan % 40
Power part auger % 41
Power part fan % 20
Power min auger % 0
Power min fan % 0
Holding min 60
Auger Feeder s 30
Sequenz code 0
Time setting
Day
Thursday
Time 18:03
Stored oper data
Total operation h
8768
El heat kWh 1234
Pellet h 3456
Max prim °C 62
Cold starts 14
Warm starts 354
Night reduction
►
Activated No/Yes
Type WeekProg
Indoor temp red °C
-2
Prim red °C -5
WeekProgram
Installer
►
Settings
Service
Operation data
Outdoor °C
-5
Indoor °C 20(20)
Boiler °C 70
FlueGas °C 160
Primfl . °C 45(45)
▼
Operation data
▲
Current A 12(20)
Pellet startphase 1K
Mixingvalve close
Program ID xxxxxxx
Program date xx-xx-xx
Operation data
▲
Heatingcirc. pump On
Elpower 3,0
▼
With indoor sensor
Without indoor sensor
With indoor sensor
Without indoor sensor
EcoFlex Thurs 8:03
Indoor °C 20.0(20.0)
Indoor Temp NR
Boiler °C 50
►
Operation data
Stored oper data
Night reduction
Installer
Indoor temp
-
● ● ● ●
+ (52)
Set. tank
►
Charge tank Yes
Temp tank °C 70
Diff °C 5
Tank prio No
3.4 Menu Indoor temperature
(the menu can be accessed directly from the main menu)
(when “operation without room sensor” is selected)
The room temperature is set in this menu if a room sensor has not been
fitted (selected in the settings menu). The house’s basic settings are first
set in the “house parameters” menu, usually with the help of the installation
contractor. Basic settings are then fine tuned using this menu.
If the indoor temperature is experienced as being too low or too high,
move the cursor t (increase) or – (reduce). Move a little at a time
and see what effect this has on indoor temperatures (1 day) before making
further changes. Several adjustments may be necessary at different outdoor
temperatures. However, a correct setting will be arrived at which will not
require further changing. A reference value (for example 50) is displayed
under the bar. This value depends on the basic value set. If the bar does not
extend far enough to allow the correct indoor temperature to be obtained,
the basic setting must be adjusted in the Installer/Settings/Setting Heating
menu. The cursor is then centred in relation to the new values.
!
radiator thermostats must be fully open and
fully functioning when adjusting the system.