CSA 96MDT SERIES, Installation Instructions Manual

Page: 15 / 100

Field Conversions
TUBE C
CUT TO F I T
CAB I NET W I DTH
N
OTE: PL
I
ERS
N
ECCESSAR
Y
TO ADD OR REMOVE CLAMPS
4B
4 b - R I GHT S I DE DRA I N OPT I ON
4 b 1 - CUT TUBE “ C ” TO F I T CORRESPOND I NG CAB I NET W I DTH .
4 b 2 - I NSERT TUBE “ C ” I NTO END “ 2 ” OF HOSE - DOUBLE ELBOW
4 b 3 - SL I DE TWO W I RE CLAMPS OVER TUBE “ C ” , SL I DE ONE W I RE CLAMP OVER
END “ 1 ” OF HOSE - DOUBLE ELBOW .
4 b 4 - I NSTALL TUBE “ C ” W I TH HOSE CLAMP AS SHOWN TO HOSE “ A ” “ PRE ASSEMBLED ”.
4 b 5 - ATTACH HOSE - DOUBLE ELBOW TO BUL K HEAD COUPL I NG POS I T I ON W I RE HOSE
CLAMP .
HOSE A
TUBE C
4A
HOSE A
4 a - LEFT S I DE DRA I N OPT I ON
ATTACH HOSE A (PRE -I NSTALLED) TO BUL K HEAD COUPL I NG .
I NSTALL HOSE CLAMP ON HOSE OVER BUL K HEAD COUPL I NG .
3
I NSTALL BUL K HEAD COUPL I NG US I NG (2) SCREWS .
I NSTALL I N JAC K ET W I TH THE BARBED F I TT I NG
PO I NTED I NTO THE VEST I BULE .
I NSTALL
2
OPT I ON DRA I N R I GHT
DETERM I NE R I GHT OR LEFT DRA I N OPT I ON .
LOCATE 7/8" HOLE I N JAC K ET S I DE .
REMOVE PLUG - D I SCARD .
DR I LL (2) Ø 1/8" HOLES FOR THE BUL K HEAD COUPL I NG .
DR I LL 1/8 ”
DR I LL 1/8 ”
7/8 ” PLUG
D I SCARD
OPT I ON DRA I N LEFT
7/8 ” PLUG
D I SCARD
1
I NSTALL I NTA K E COUPL I NG I N TOP PLATE .
I NSTALL
UP
F
LOW VERT
I
CAL VE
N
T
NOTE: THESE CONVERS I ON I NSTRUCT I ONS ARE I NTENT I ONALLY GENER I C, SOME PARTS MAY BE D I FFERENT I N YOUR FURNACE
ST - A1194 - 28 - 03
PARTS NEEDED:
PARTS NEEDED FOR TH I S CONVERS I ON RE Q U I RE I TEMS
FROM THE
PARTS BAG
ONLY . NO OTHER CONVERS I ON
KI TS ARE NEEDED .
!
TUBE C
BUL K HEAD
COUPL I NG
FROM PARTS BAG (PROV I DED W I TH UN I T)
(X2)
# 8 X 1/2"
SCREW
HOSE
CLAMP
I NTA K E
COUPL I NG
W/ NUT
DR I LL
1/8" DR I LL B I T PL I ERS
1/4" HEX HEAD DR I VER TUB I NG CUTTER
TOOLS/MATER I ALS NEEDED:
"*3
'-08
(X3)
(X3)
HOSE -
DOUBLE ELBOW
1
2
HOSE -
DOUBLE ELBOW
15