background image

  

 

Instruments decription 

 
VA 525 EN V1.01 

 

Page 5 of 41 

1  Intended use 

The VA 525 consumption sensor is used for continuous flow measurements. 

 

The VA 525 consumption sensor is designed and constructed exclusively for the intended purpose 
described here and may only be used accordingly. 

 

The user must check whether the instrument is suitable for the selected application. It must be 
ensured that the medium is compatible with the wetted parts. The technical data listed in the data 
sheet are binding. 

 

Improper handling or operation outside the technical specifications is not permitted. Claims of any 
kind based on improper use are excluded. 

 

Operating principle: 

The VA 525 consumption probe operates according to the calorimetric measuring method. 

 

The basis of this measuring method is the electrical heating of the mechanically protected built-in 
sensor. The mass flow, the volume flow and the flow velocity can be measured and determined by 
the resulting heat flow to the passing medium (gas). 

 

With the calorimetric measurement method (based on the measurement principle), the operating 
temperature and pressure of the medium have no influence on the measurement result, only the 
material data of the gas component are decisive. 

 

2

 

Safety instructions 

 

Please read carefully before starting the device! 

 

Warning: Do not exceed the pressure range of 16 bar!  

Observe the measuring range of the sensor! 

Always observe the direction of flow when positioning the sensor! 

The screwed fixture must be pressure tight. 

It is absolutely necessary to avoid condensation on the sensor element or water drops in the 
measuring air as they may cause faulty measuring results. 

The manufacturer cannot be held liable for any damage which occurs as a result of non-
observance or non-compliance with these instructions. Should the device be tampered with 
in any manner other than a procedure which is described and specified in the manual, the 
warranty is cancelled and the manufacturer is exempt from liability. 

The device is destined exclusively for the described application. 

We offer no guarantee for the suitability for any other purpose and are not liable for errors 
which may have slipped into this operation manual. We are also not liable for consequential 
damage resulting from the delivery, capability or use of this device. 

We offer you to take back the instruments of the instruments family VA 525 which you would 
like to dispose of. 

Qualified employees from the measurement and control technology branch should only carry 
out adjustments and calibrations. 

 

Summary of Contents for VA 525










































Reviews: