Crystal Vision Indigo TANDEM 320 User Manual Download Page 48

Page: 48 / 62

Crystal Vision

Specification

8 Specification

General

Dimensions 100mm x 266mm module with DIN 41612 connector.

Weight 200g.

Power

consumption

TANDEM 320 - 9.3 Watts.

Inputs

Video Two video inputs: one for Ch. A and one for Ch. B.

HD or SD SDI 270 Mb/s to 2.970 Gb/s serial digital compliant to EBU
3267-E, SMPTE 259, SMPTE 292-1 and SMPTE 424/425-A.

Cable Equalisation:

3G (2.970Gb/s) – 80 metres, Belden 1694A or equivalent.

HD (1.485Gb/s) – 120 metres, Belden 1694A or equivalent.

SD (270Mb/s) >200 metres, Belden 8281A or equivalent.

Automatic de-embedding to SMPTE 272 or SMPTE 299-1.

Video

standards

supported

1080p50/59.94, 1080i50/59.94, 720p50/59.94, 1080psf23.98/24, PAL,
NTSC. Input format auto selected.

Return loss 50Mhz to 1.5GHz -15dB.

Audio Up to four 24 bit stereo pairs or two analogue pairs per channel. AES3

110 ohm or HiZ (balanced) D-Type, or AES3-id (unbalanced) 75 ohm
BNC. Synchronous 48kHz audio to video.

Outputs

Video Two video outputs: one for Ch. A and one for Ch. B

Serial output: 270Mb/s to 2.970Gb/s serial compliant to EBU 3267-E,
SMPTE 259, SMPTE 292-1 and SMPTE 424/425-A.

Output follows the input format.

Audio is embedded to SMPTE 272 or SMPTE 299-1.

Audio Up to four 24 bit stereo pairs or two analogue pairs per channel AES:

110 ohm balanced D-Type or 75 ohm unbalanced BNC.

Rear Module I/O

RM71

RM72

Two video inputs and outputs (one each per channel) with 110 ohm
balanced audio on a high density D-Type.

Two video inputs and outputs (one each per channel) with eight 75 ohm
unbalanced audio on BNCs.

TANDEM 320 User Manual R1.3

11 July 2019

Summary of Contents for Indigo TANDEM 320































































Search results

Summary of Contents for Indigo TANDEM 320

Reviews:

Related manuals for Indigo TANDEM 320

Brands by name

Popular brands

Crystal Vision Indigo TANDEM 320, User Manual

Search results

Summary of Contents for Indigo TANDEM 320

Reviews:

Related manuals for Indigo TANDEM 320

Brands by name

Popular brands