Crystal Vision Indigo TANDEM 320 User Manual Download Page 47 | Manualshive

Page: 47 / 62

background image

Crystal Vision

Troubleshooting

7 Troubleshooting

Card edge monitoring

The front edge of the card provides useful power rail monitoring and input status.

TANDEM 320 front edge view

See

Card Edge Controls

for explanation of card edge LEDs.

The card edge LEDs and 10-digit display may be used in conjunction with status information
from any connected remote status panel display or from VisionWeb if available.

Board edge control was removed from TANDEM 320 in 2018. Therefore the card edge control
information is only relevant for older versions of the product.

Basic fault finding guide

The Power OK LEDs are not illuminated

Check that the frame PSU is functioning – refer to the appropriate frame manual for detailed
information

There is no video output

Check that a valid SDI input is present and that any cabling is intact

The video output exhibits jitter

Check that the input SDI stability is within normal limits

The card no longer responds to card edge or front panel control

Check that the card is seated correctly and that the Power OK LEDs are lit

Check any active control panel cabling

Check if the control panel can control another card in the same rack

If necessary reset the card

Resetting the card

If required, the card may be reset by removing the card from the rack and then re-inserting it

It is safe to re-insert the card whilst the rack is powered. Any previous configuration will be
retained, use a factory reset to erase any configurations stored in the card

TANDEM 320 User Manual R1.3

46

11 July 2019

«
...
45
46
47
48
49
...
»

Summary of Contents for Indigo TANDEM 320































































Reviews:

No comments

Related manuals for Indigo TANDEM 320

Brand: xpr Pages: 10

Brand: ICP DAS USA Pages: 92

Brand: Sunpak Pages: 8

Brand: IDTECK Pages: 12

Obid ID RWA02.ABC-A

Brand: Feig Electronic Pages: 36

Radeon X1300PCI

Brand: Diamond Multimedia Pages: 1

RX9600PRO-TD128

Brand: MSI Pages: 2

NVIDIA Quadro FX 3450

Brand: HP Pages: 3

NVIDIA Quadro FX 3400

Brand: HP Pages: 2

Brand: Lava Pages: 4

Brand: Sebury Pages: 14

Brand: ACTpro Pages: 12

Brand: GE Interlogix Pages: 34

Brand: GE Interlogix Pages: 36

Brand: AAxeon Pages: 4

Orbit Reader 20

Brand: Orbit Research Pages: 57

Brand: Diablotek Pages: 1

Brand: Brivo Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands