Crystal Vision Indigo TANDEM 320 User Manual Download Page 20

Page: 20 / 62

Crystal Vision

Control and Status monitoring

Reading card edge LEDs

Card edge LEDs may be used in conjunction with status information from any connected
remote status panel display or from VisionWeb if available.

Refer also to the troubleshooting chapter for more help with solving problems and monitoring
status information.

The following table summarises the card edge LED functions and colours:

LED Name

LED

Colour

Function when ON

Function when Off

PSU

Green

Good power supply (PSU) rails

One or more of the monitor
supplies is out of specification

Lock

Green

Yellow

Video input A standard is HD
(High Definition)

Input not present

Yellow

Video input A standard is SD
(Standard Definition)

Yellow

Video input B standard is HD
(High Definition)

Input not present

Yellow

Video input B standard is SD
(Standard Definition)

Yellow

Audio Group 1 present Ch. A

Audio Group 1 not present

Yellow

Audio Group 2 present Ch. A

Audio Group 2 not present

Yellow

Audio Group 1 present Ch. B

Audio Group 1 not present

Yellow

Audio Group 2 present Ch. B

Audio Group 2 not present

Navigating card edge menus

To access the card edge menu system proceed as follows:

•

Press the up-arrow [

] until a top menu category is reached

•

Rotate the SCROLL/ADJ control until the desired menu category is found

•

Press ENTER to enter the sub-menus of that category

•

Rotate SCROLL/ADJ to select a sub-menu

•

Press ENTER to select the desired function. Selection will be indicated by the text
being displayed in

italic

text

•

Rotate ADJUST to make the desired change to the selected parameter. The display
changes to

italics

to indicate that a change has been made and requires confirmation

•

When required push ENTER to action the change. The display will return to normal
non-italic text.

•

Use the up-arrow [

] and SCROLL/ADJ control to navigate to further menus

TANDEM 320 User Manual R1.3

11 July 2019

Summary of Contents for Indigo TANDEM 320































































Search results

Summary of Contents for Indigo TANDEM 320

Reviews:

Related manuals for Indigo TANDEM 320

Brands by name

Popular brands

Crystal Vision Indigo TANDEM 320, User Manual

Search results

Summary of Contents for Indigo TANDEM 320

Reviews:

Related manuals for Indigo TANDEM 320

Brands by name

Popular brands