background image

Crystal Vision

 

Installation

 

Crystal Vision 

 

Installation

 

 

2   Installation 

These servicing instructions are for use by qualified personnel only. To reduce risk  of electric 

shock, do not perform any servicing other than that contained in the  Operating Instructions 

unless you are qualified to do so. Refer all servicing to qualified service personnel. Refer also to the 

General Safely Summary below. 

 

 

General Safety Summary 

The following warnings are intended for user guidance and safety. 

Ground   

This product must be grounded through the grounding conductor of the 

power cord. 

 

Power cable   

Use only power cords that meet the required specification for this product. 

 

Fuses   

To avoid fire hazard use only fuses of the type and rating specified. 

 

Service   

These servicing instructions are for use by qualified personnel only. To 

reduce risk of  electric shock, do not perform any servicing other than that 

contained in this manual unless  you are qualified to do so. Refer all 

servicing to qualified service personnel. 
Apart from procedures described in this manual there are no user serviceable 

parts within  the frame. If the frame requires any other servicing it should 

be returned to the manufacturer  or dealer. 
On no account should the unit be powered whilst any covers are removed. 

 

Ventilation 

The unit must have adequate ventilation. Installation should be in standard 19" 

racks  with  cool air  circulation  available  at  the  front.  The  left  and right 

ventilation grilles must not be  obstructed. 

 

EMC   

To comply with EMC regulations the following guide lines 

should be observed:  Do not operate this unit for extended periods 

with the front panel open. 

Do not use the frame unless all the rear connector positions are filled, 

either with Crystal  Vision Rear Modules, or with Crystal Vision 

blanking plates. 
Do not operate the equipment with covers or panels removed. 

 

General   

To avoid electric shock do not operate this product in wet or damp 

conditions. 

To avoid injury or fire hazard do not operate this product in an 
explosive atmosphere.  Only use this rack in conjunction with Crystal 
Vision modules designed for that purpose.

 

Indigo PSU Manual R1.2 

24/05/2010 

4

 

 

Summary of Contents for Indigo PSU-160i


















Reviews: