Crystal Vision DEC104S User Manual Download Page 40

Page: 40 / 40

Crystal Vision

Specification

DEC104S User Manual R1.0

29/10/04

Ordering information

DEC104S

10 bit PAL/NTSC or Y/C to SDI adaptive comb decoder with
TBC/framestore and additional bandsplit decoding in PAL

RM01

Single height rear connector

RM23

Single height rear connector

RM24

Single height rear connector

RM25

Triple height rear connector

RM27

Double height rear connector

Indigo 4

4U frame for up to 24 modules

Indigo 2

2U frame for up to 12 modules

Indigo 1

1U frame for up to 6 modules

Indigo DT

1U Desk top box for up to 2 modules

Indigo 2A

2U frame, Statesman enabled, with active control panel for up 12
modules

Indigo 1A

1U frame, Statesman enabled, with active control panel for up 6
modules

Indigo DTA

1U Desk top box, Statesman enabled, with active control panel for
up 2 modules

Indigo 4S

Statesman enabled only 4U frame for up to 24 modules

Indigo 2S

Statesman enabled only 2U frame for up to 12 modules

Indigo 1S

Statesman enabled only 1U frame for up to 6 modules

Indigo DTS

Statesman enabled only 1U Desk top box for up to 2 modules

Summary of Contents for DEC104S









































Search results

Summary of Contents for DEC104S

Reviews:

Related manuals for DEC104S

Brands by name

Popular brands

Crystal Vision DEC104S, User Manual

Search results

Summary of Contents for DEC104S

Reviews:

Related manuals for DEC104S

Brands by name

Popular brands