Cryomech CPA289C Installation And Operation Manual Download Page 26

Page: 26 / 64

Specifications

5-6

9. System I/O Port

A DB15 female socket that can be used to remotely control the helium compressor package
and monitor a limited number of its parameters.

10. Cold Head Motor Connector

The electrical connection for the cold head motor cord, from the helium compressor package
to the cold head or remote motor assembly.

11. Main Circuit Breaker

Provides over-current protection for the helium compressor package and functions as a power
disconnect.

12. Power Cord

Electrical connection that supplies power to the system.

13. Cooling Water Inlet Connection

A 3/8 FPT (Female National Pipe Thread) fitting used to provide coolant to the helium
compressor package.

14. Cooling Water Outlet Connection

A 3/8 FPT (Female National Pipe Thread) fitting used as an exit for the coolant from the helium
compressor package.

15. Touch Screen

Displays system status, warnings, error messages, operation data, system information and
allows users to interact with the helium compressor package.

16. COM Ports

Used for remote monitoring and control of the system via SMDP or Modbus RTU protocol.

Summary of Contents for CPA289C

































































Search results

Summary of Contents for CPA289C

Reviews:

Related manuals for CPA289C

Brands by name

Popular brands

Cryomech CPA289C, Installation And Operation Manual

Search results

Summary of Contents for CPA289C

Reviews:

Related manuals for CPA289C

Brands by name

Popular brands