TO FACTORY
HARNESS
22-PIN
(male plug)
8-PIN
(male plug)
22-PIN
(female plug)
WHITE
/ 12V REVERSE OUTPUT
VIDEO-IN
(female plug)
TO FACTORY
DISPLAY
22-PIN
(female plug)
22-PIN
(male plug)
WHITE
WHITE
WHITE
GRAY
VIDEO HARNESS
CAMERA POWER
VIDEO RCA
(SIGNAL FROM CAMERA)
*Camera not provided
CAMERA
INCLUDED
TAP GROUND
ON
BLACK
WIRE OF
8-PIN CONNECTOR
TAP BLACK WIRE HERE
8-PIN CONNECTOR
4 5 6
ON
1 2 3
STATUS LED’S
work. Following these instructions from “Start” to” Finish” will ensure a
smooth and hassle free installation.
822-1348. We are here to help.
PARTS INCLUDED:
(1) Universal Bullet Camera
(1) 15 ft. Extension
(1) CH-75E Interface
(2) CH-75E Harness
(1) Instruction
- Lens Angle 170 Degrees
- Resolution 420 TV Lines
- Min. Illumination 0.2Lux
- Voltage 12v
- Operating T
LTWá-á-
- NTSC
- Reference Lines
:O\[[LY:WLLKZ\Z
- Waterproof
7P_LSZ_
PRECAUTIONS:
- Remove the negative side of the battery to avoid any short circuits
during the installation.
- Do not install the interface near any major components or near the
HVAC system. This may cause damage or overheating to the vehicle.
Please read the entire manual before installing this interface.
Chrysler
2011 - 2015 300
Dodge
2011 - 2015 Charger
2011 - 2015 Journey*
Notes:
*Dodge Journey requires different
camera (not included in kit), available
upon customer request.
Important Note: Not compatible in
vehicles with Manual Transmission.
IMPORTANT:
Compatible Radio Type:
U-CONNECT 8.4” SCREEN
RVCCH-75EC
CONNECTIONS OVERVIEW
The parking lines are there to assist you while reversing.
What the lines mean:
Yellow Line: CLEAR
Green Line: GETTING CLOSE
Red Line: WARNING - VERY CLOSE
RED
GREEN
YELLOW
INSTALLING THE CAMERA AND INTERFACE
1. From inside the trunk, remove the third brake light from the trunk lid.
2. Drill a whole on the old brake light as shown on page two, then
route your power and video wiring towards the front. (See page 3)
3. Remove the factory radio to gain access to the factory
connectors. Connect behind the radio not behind the display.
5. Route the wires from the camera towards the radio and make the
power and video connections. For powering up the camera,
use the WHITE 12v output wire from the Can-Bus interface.
We recommend using the BLACK wire from the 8-Pin molex
connector. See below.
REAR-VIEW INTEGRATION FOR CHRYSLER & DODGE VEHICLES 2011-2015 w/ 2-PIECE RA
DIO
PARKING LINE
Rev. 032015
MAKE SURE TO TEST THE CAMERA ANGLE BEFORE
RE-INSTALLING THE TAILGATE COVER.
U-CONNECT 8.4” SCREEN
(2-PIECE RADIO)
Dip 1:
Not Used.
Dip 2:
Activates the Rear-View Camera image when the vehicle is in
reverse gear.
Dip 3:
Not Used
Dip 4:
Not Used
Dip 5 & 6:
Varies, these switches are defaulted both to OFF.
If the radio is having turn-on issues please try the following:
([[LTW[6UL!:L[IV[O[V[OL65WVZP[PVU
Attempt T
^V!:L[[V6UHUK[V6-
F.
Attempt Thr
LL!:L[[V6--HUK[V65
If none of the above solutions work out for your vehicle please
contact tech support.
SETTING THE DIP SWITCHES
4 5 6
ON
1 2 3
TAP HERE/
BLACK WIRE
USING THE 8-PIN FOR GROUND
We recommend using the BLACK wire on the 8-Pin connector.
See picture below for where to tap.
LED STATUS:
RED LED
BLUE LED:
Pulsing = No BUS, Pending DATA
OFF = Complete Power Down
Solid = BUS Recognized
