background image

INTERFACING SOLUTIONS

RVCAD-81M

REAR-VIEW CAMERA INTEGRATION 

FOR SELECT AUDI VEHICLES

with MMI 3G + 4G SYSTEMS

AUDI

2012 - 2014  A4
2012 - 2014  A5
2012 - 2014  A6
2012 - 2014  A7
2012 - 2014  A8
2012 - 2014  Q5
2012 - 2014  Q7

APPLICATION NOTES:

THIS INTERFACE REQUIRES THE

VEHICLES TO HAVE THE MMI

SYSTEM INSTALLED

WORKS FOR:

MMI Radios/ 4-Pin LVDS/ 3G + 4G

This interface does not o er the 

Force RVC feature. 

Contact Tech Support for more 

information.

SAFETY PRECAUTIONS

1. Please read through the entire instruction manual before starting any of the installation procedures.
2. We recommend disconnecting the negative side of the battery until ready to code the vehicle.
3. Do not install any of the main modules near any major components or near the HVAC system,
    as placing items near the HVAC may cause damage or overheating to the vehicle or interface.
4. We recommend not disconnecting any of the air bag connections behind the dash panels.
5. This product is under Crux’s 1 year manufacturer’s warranty. Warranty may be voided in the case where 
    the device shows proof of being opened or improper extreme force.

TECH SERVICES

All our products are manufactured under strict quality control. Each device is tested before shipment. If you have any problems or if 
you need technical support, contact us directly:

Crux Interfacing Solutions Tech Support
1 (855) 822-1348 (Mon - Fri - 9:00 AM - 5:00 PM) 

 Time

www.cruxinterfacing.com

 

5

1

6

0

7

0

.

v

e

R

1

PARTS INCLUDED

12-Pin Audio Input/Output

Cable

CUL-03

Camera

4-Pin Switcher Remote

6-Pin RGB Input Cable

AD-81M Main

Interface Module

Summary of Contents for RVCAD-81M









Reviews: