CXM2000 Monitor and Crossover System
CXM2000
影院扬声器优化/监听系统
page 20
Operation Manual
操作手册
Appendix V. Control ASCII Protocol
附录五、控制ASCII协议
Connecting the CXM2000 to PC via RS-232 connector allows the fault detection details to be viewed. The command protocol between the CXM2000 and basic cinema system is the ASCII protocol, which is used to implement the fault detection management.
通过RS-232接口可以连接CXM2000至PC，以查看故障检测所得信息。该连接使用下表所示的ASCII协议，可以实现故障检测管理的功能。
7 Appendix
(continued)
7.附录
（接上一页）
Input Command
输入命令
Feedback from CXM2000
返回信息
Note
详情
CXM2000 System Status Inquire
All system Amplifiers and speakers are GOOD.
L Low Frequency Amplifier status is Fault.
L Low Frequency Speaker status is Fault.
L High Frequency Amplifier status is Fault.
L High Frequency Speaker status is Fault.
R Low Frequency Amplifier status is Fault.
R Low Frequency Speaker status is Fault.
R High Frequency Amplifier status is Fault.
R High Frequency Speaker status is Fault.
C Low Frequency Amplifier status is Fault.
C Low Frequency Speaker status is Fault.
C High Frequency Amplifier status is Fault.
C High Frequency Speaker status is Fault.
L Amplifier status is Fault.
L Speakers status is Fault.
R Amplifier status is Fault.
R Speakers status is Fault.
C Amplifier status is Fault.
C Speakers status is Fault.
SW1 Amplifier status is Fault.
SW1 Speakers status is Fault.
SW2 Amplifier status is Fault.
SW2 Speakers status is Fault.
LS Amplifier status is Fault.
LS Speakers status is Fault.
RS Amplifier status is Fault.
RS Speakers status is Fault.
BSL Amplifier status is Fault.
BSL Speakers status is Fault.
BSR Amplifier status is Fault.
BSR Speakers status is Fault.
All channels are good
Bi-Amp mode
Bi-Amp mode
Bi-Amp mode
Bi-Amp mode
Bi-Amp mode
Bi-Amp mode
Bi-Amp mode
Bi-Amp mode
Bi-Amp mode
Bi-Amp mode
Bi-Amp mode
Bi-Amp mode
Passive mode
Passive mode
Passive mode
Passive mode
Passive mode
Passive mode
SW1 is available
SW1 is available
SW2 is available
SW2 is available
CXM2000 System Configuration
L, R, C screen Speaker is JBL “XXXXXXXX”
Speaker is “XXXXXXXX”
Fault detection is “XXXXXXXX”
System is “X.1” Speaker
SW1 is “XXXXXXXX”
SW2 is “XXXXXXXX”
Application Version is “XXXXXXXX”
HW Version is “X”
Speaker Name
“Bi-Amp” or “Passive”
“Enable” or “Disable”
“5.1” or “7.1”
“Enable” or “Disable”
“Enable” or “Disable”
A, B, C, D…
* The data is all in ASCII format. If the input command cannot be recognized, it will prompt the information below:
*
所有数据都为ASCII格式。如果输入的命令不能被识别，将会提示以下信息：
Invalid Command
1) CXM2000 System Configuration
2) CXM2000 System Status Inquire
Appendix VI. Communication Settings
附录六、通讯设置
Item
Specification
Operating Mode
Full Duplex
Hardware Handshaking
None
Flow control
None
Synchronous system
Asynchronous
Transmission
9600
Data Length
8 bits
Parity
None
Stop Bit
1
