Crown CT42049, Original Instructions Manual

Page: 16 / 76

16
English
Installation and regulation of appliance
elements
Before performing all the procedures, disconnect
the appliance from AC mains and water supply
system.
Do not draw up the fastening elements
too tight to avoid damaging the thread.
Mounting / dismounting / setting-up of
some elements is the same for all appli-
ance models, in this case specific mod -
els are not indicated in the illustration.
Installing / removing the rear holder (see fig. 1)
• Install rear holder 9 as shown in fig. 1. Tighten
screws 22 �
• Disassembly operations do in reverse sequence�
Installing / removing the wheels (see fig. 2)
[CT42050]
• Install wheels 3 as shown in fig. 2.
• Disassembly operations do in reverse sequence�
Installing / removing the handle (see fig. 3)
• Install handle 1 as shown in fig. 3. Tighten screws 23 �
• Disassembly operations do in reverse sequence�
Installing / removing the washer gun holder (see
fig. 4)
• Install washer gun holder 2 as shown in fig. 4.
• Disassembly operations do in reverse sequence�
Installing / removing / adjusting spray gun (see
fig. 5-7)
•
Insert jet pipe 13 into extension tube 14 � Attention:
mounting ledge onto jet pipe 13 should be comes
into the groove onto the extension tube 14 (see
fig. 5.1).
• Insert extension tube
14
into spray gun
15
as shown
in fig. 5.2.
• Disassembly operations do as shown onto fig. 6.
• You can change stream pattern by rotating jet
pipe
13
tip (see fig. 7.1).
Installing / removing quick-release coupling and
filter for self-priming operation (see fig. 8)
• Install quick-release coupling
19
on the hose
20
as
shown onto fig. 8.1.
• Put hose clamp 26 on the end of hose 20 � Install
filter 17 in the hose 20 and fix it with hose clamp 26
(see fig. 8.2).
• Disassembly operations do in reverse sequence�
Installing / removing the filter (see fig. 9)
• Insert filter element 28 into filter housing 27 (see
fig� 9�1)�
• Screw filter 18 on inlet fitting 11 (see fig. 9.2).
• Disassembly operations do in reverse sequence�
Quick-release coupling (see fig. 10)
• To connect, insert ("click") quick-release coupling 19
onto quick-release adapter of filter 18 or quick-release
adapter installed onto water supply tap (see fig. 10.1).
• To disconnect, move back the bushing of the quick-
release coupling 19 as shown in the fig. 10.2 and
remove the quick-release coupling
19
from the quick-
release adapter of filter 18 or quick-release adapter
installed onto water supply tap�
Connecting pressure hose to the spray gun (see
fig. 11.1)
• To connect, insert ("click") pressure hose 21 fitting
into spray gun 15 hole (see fig. 11.1).
• To disconnect, press lock
29
and remove pressure
hose 21 fitting from spray gun 15 hole�
Connecting pressure hose to the appliance (see
fig. 11.2)
• To connect, insert ("click") pressure hose 21 fitting
into outlet fitting 6 (see fig. 11.2).
• To disconnect, move lock 5 as shown onto fig. 11.2
and remove pressure hose 21 fitting from outlet fitting 6 �
Water connection (see fig. 12-14)
Always use filter 18 as the contaminants
contained in the water may damage the
appliance.
Connecting to the water supply system (see
fig. 12, 9.2)
• To ensure sufficient water supply, use the shortest
possible hose (minimal diameter, 13 mm, or 1/2"); if
the hose is longer than 10 m, its min� diameter shall
be 19 mm (3/4")�
• Quick-release couplings 19 shall be installed on both
ends of the hose, which will ensure quick and reliable
connection� Attention: metal hose couplings with
" Aquastop " leakage protection system may damage
the appliance. Use plastic hose couplings instead.
•
Install quick-release adapter on the water supply tap�
• Connect one end of the hose 20 to the water supply
tap, and the other one to the filter 18 (see fig. 9.2).
Using water reservoirs (see fig. 13-14)
The appliance has the self-priming function that allows
to draw water from reservoirs, water bodies, etc�
Attention: the elevation difference between the
filter 17 and the appliance must not exceed 2 m.
• Connect one end of the hose 20 (with installed
quick-release coupling 19 ) to the filter 18 (see fig. 13).
• Immerse second end of the hose 20 (with installed
filter 17 ) in reservoir with water�
•
Attention: the filter 17 should not be too close
to the surface of water (see fig. 14.1) as it can lead
to draw of air, and should not lie on the bottom
of reservoir or water body (see fig. 14.2) as the
filter 17 may become clogged, and the appliance
will work with overload.
Assembly / disassembly / installation of detergent
spray nozzle (see fig. 15)
• Fig� 15�1 shows how to remove / install the tank of
the detergent spray nozzle 12 �