Crown Royal Stoves RS7300E Owner'S Manual Download Page 41

41

AUTHORIZED FURNACE TREATMENT

P: 866-361-7355 

F: 218-283-5786 

W: www.crownroyalstoves.com

Greentech Manufacturing, Inc.    2716 Crescent Dr    International Falls   MN   56649

Greentech Manufacturing Inc. requires the usage of authorized furnace treatment to be used in all Crown Royal Stoves. Treatment is 
to be added to furnace water upon initial start up and is required to remain at satisfactory levels thought the life of the stove.

To ensure the maximum efficiency and longevity of your Crown Royal Stove, water treatment is crucial. Treating systems with 
authorized furnace treatment will prevent corrosion and scale buildup. Calcium and magnesium are commonly found in many water 
supplies. These impurities cause layers of scale that not only decrease heat transfer efficiency but cause pitting on the interior water 
jacket. Over time constant pitting will result in leaks. Once authorized treatment is added it creates the necessary barrier needed to 
prevent the breakdown of metals. Premature corrosion is a result of not treating the water with correct corrosion resistant inhibitor 
or with the wrong dosage.

Water Treatment and Testing Required on all Crown Royal Stoves

All Crown Royal Stoves are required to be shipped with initial recommended gallon(s) of 
authorized treatment. Crown Royal Stoves are backed with a 20 Year Limited Warranty. To retain 
warranty on Crown Royal Stoves it is required to use recommended treatment and submit 
annual samples for testing. Failure to maintain treatment at recommended levels and annual 
water testing will result in a voided warranty.

 

•   Specifically designed for Crown Royal Stoves, closed-loop design.

 

•   Helps protect system from scale, sludge and corrosion.

 

•   Vapors help prevent corrosion throughout the furnace.

 

•   Economical – one gallon/3.78 liters treats 300 gallons/1134 liters of system capacity.

 

•   FREE Water Testing and sample bottles.

Sample Bottles 

Two sample bottles and labels are found with each gallon of treatment.  For additional bottles or labels please contact your local 
dealer or call 866-361-7355.

Warning  

Read entire label located on treatment before opening or using this product.  Keep out of the reach from children.  Do not mix with 
any other chemicals.  Contains Sodium Nitrate and Potassium Hydroxide. Avoid contact with skin, eyes and clothing.  Undiluted 
product causes severe skin and eye irritations.  Wash thoroughly after handling. Do not swallow. Swallowing may cause nausea, 
vomiting, weakness and lowered blood pressure. MADE IN U.S.A.

Storage 

Keep container closed when not in use.  When product is stored it may separate or thicken.  This will not harm the performance.  
Before using, warm to room temperature and stir thoroughly. Keep from freezing.

Summary of Contents for RS7300E



























































Reviews: