Crow OLED Keypad User Manual Download Page 2

 

 

 

Crow Limited Warranty 

Crow warrants this product to be free from defects in materials and workmanship under normal use and service for 

a  period  of  one  year  from  the  last  day  of  the  week  and  year  whose  numbers  are  printed  on  the  printed  circuit 
board inside his product. 

Crow’s obligation is limited to repairing or replacing this product, at its option, free of charge for materials or labor, 
if  it  is  proved  to  be  defective  in  materials  or  workmanship  under  normal  use  and  service.  Crow  shall  have  no 

obligation under this Limited Warranty or otherwise if the product is altered or improperly repaired or serviced by 
anyone other then Crow. 

There are no warranties, expressed or implied, of merchantability or fitness for a particular purpose or otherwise, 
which  extend  beyond  the  description  on  the  face  hereof.  In  no  case  shall  Crow  be  liable  to  anyone  for  any 

consequential or incidental damages for breach of this or any other warranty, expressed or implied, or upon any 
other basis of liability whatsoever, even if the loss or damage is caused by Crow’s own negligence or fault. 

Crow does not represent that this product can not be compromised or circumvented; that this product will prevent 
any person injury or property loss or damage by burglary, robbery, fire or otherwise; or that this product will in all 

cases  provide  adequate  warning  or  protection.  Purchaser  understands  that  a  properly  installed  and  maintained 
product can only reduce the risk of burglary, robbery or other events occurring without providing an alarm, but it is 

not insurance  or a guarantee that  such will not  occur or that there will be no personal  injury or property loss or 
damage  as  a  result.  Consequently,  Crow  shall  have  no  liability  for  any  personal  injury,  property  damage  or  any 

other  loss  based  on  claim  that  this  product  failed  to  give  any  warning.  However,  if  Crow  is  held  liable,  whether 
directly or indirectly, for any loss or damage arising under this limited warranty or otherwise, regardless of cause 

or origin, Crow’s maximum liability shall not in any case exceed the purchase price of this product, which shall be 
the complete and exclusive remedy against Crow. 

©  2010. All rights reserved. 

Information in this document is subject to change without notice. No part of this document may be reproduced or 

transmitted in any form or by any means, electronic or mechanical, without express written permission of  
 

Print version 001 

 

 

 

Summary of Contents for OLED Keypad





























Reviews: