background image

CROSSRUNNER  50 ATV

ReAssembly Guide

ATTENTION:

Always read everything before doing anything. 

This will help you to know that you have access 
to  all  the  tools,  information,  and  help  you  may 
need  to  perform  all  the  steps  outlined  in  this 
manual.  Your  attention  to  detail  is  critical  in 
providing  a  safe  and  reliable  product  to  your 
customer.  There  cannot  be  enough  emphasis 
placed  on  safety  when  assembling  or  servicing 
this  ATV.  You  will  be  referencing  the  Owner’s 
Manual, the battery service instructions, and the 
tire  pressure  information  sticker  on  the  front 
fender as well as the Re-assembly Manual during 
this  procedure.  If  you  have  any  questions  or 
concerns  pertaining  to  the  assembly  or  the 
information  found  in  this  booklet,  please  call 
888-520-7222

NOTE:  This  ATV  should  be  assembled  by  the 
selling  dealer  only.  The  end  user  should  never 
do the final assembly or inspection of this ATV.

© Copyright North American Imports, LLC

This work may not be copied and distributed without express written consent .

3

Summary of Contents for 50 ATV





















Reviews: