background image

INSTRUCTION MANUAL

MODELS 2005-02P4 and 2005-03P4 Upconverters

 

TABLE OF CONTENTS

PAGE

Warranty

2

1.0 General

3

1.1  Equipment Description

3

1.2  Technical Characteristics

4

2.0 Installation

5

2.1  Mechanical

5

2.2  Front Panel Controls and Indicators

5

2.3  Rear Panel Inputs, Outputs, and Controls

5

2.4  Accessing the PC Card

6

2.5  Operation

7

3.0 Environmental Use Information

8

WARRANTY - The following warranty applies to all Cross Technologies, Inc. products.

All Cross  Technologies, Inc. products are warranted against defective  materials and 
workmanship for a period of one year after shipment to customer.  Cross Technologies, Inc.’s 
obligation under this warranty is limited to repairing or, at Cross Technologies, Inc.’s option, 
replacing parts, subassemblies, or entire assemblies.  Cross Technologies, Inc. shall not be 
liable for any special, indirect, or consequential damages.  This warranty does not cover parts 
or equipment which have been subject to misuse, negligence, or accident by the customer 
during use.  All shipping costs for warranty repairs will be prepaid by the customer.  There 
are not other warranties, express or implied, except as stated herein.

C

ROSS 

T

ECHNOLOGIES, INC.

6170 Shiloh Road

Alpharetta, Georgia 30005

(770) 886-8005

FAX (770) 886-7964

Toll Free 888-900-5588

WEB www.crosstechnologies.com 

E-MAIL [email protected]

2005-02/03 Manual, Rev. J

 Page 2  

  

               08/14/2019

Summary of Contents for 2005-02P4










Reviews: