background image

JP10, JP110 DO NOT ADJUST THESE!

JP15, JP16, JP17, JP18 - DO NOT ADJUST THESE!

JP25,JP125 - DO NOT ADJUST THESE!

JP26,JP126 - DO NOT ADJUST THESE!

2.4.2  On-Card Switches 
S3, S103 - Initial Channel Select (ICS) Mode
- 4-position DIP switch Selects the Initial Channel Select mode 

when JP1,2,3, JP101,102,103,in Dot and JP4, JP104 in Non-dot.

S3, S103 positions 1,2,3,4 to ON - ICS is enabled. In the ICS mode, the initial channel can be either 
CH1 or CH2 by switching the front panel Manual Select switch to either CH1 or CH2 and then back to 
the Auto position.or by grounding either Remote 1 or Remote 2 pins on J8 and then grounding the 
Remote reset pin on J8 causing the 1582-14 to go back to Auto in the channel last selected remotely if 
both channel alarms are clear or both channels are in alarm. The initial channel can also be selected if 
both channel alarms are clear or both channels are in alarm..
S3, S103 positions 1,2,3,4 to OFF - ICS is disabled (Minimum Auto switching, Return to Last 
State Mode)
 The 1582-14 goes to the last state (CH1 or CH2) it was in when in Auto after Manually or 
Remotely switching and returning to Auto. Auto switching occurs only if current channel alarms and the 
other channel is clear.
S3, S103 normal position - 1,2,3,4 to ON

S4, S104 - DO NOT ADJUST THESE!

S5, S105 DO NOT ADJUST THESE!

1582-725 Manual, Rev. B

 

 

  Page 8

    

          4/10/14

Summary of Contents for 1582-725













Reviews: