background image

MODEL 1582-725 RF Switch

1.0  General

1.1  Equipment Description 

- The 1582-725 RF Switch has two independent switches (A and B) in a single 1 

3/4” chassis. Each switch provides Auto, Manual, or Remote relay switching between CH1 and CH2. Alarm 
conditions on CH1 and CH2 are detected if a contact closure (to ground or an open, selectable) occurs. 
Switching logic can be selected as follows:

1) CH1 Prime Mode

 - Switches from CH1 to CH2 only if CH1 alarms and CH2 is good. 

Switches back to CH1 when it is no longer in alarm or when both CH1 and CH2 are in alarm.

2) Latch to CH2 Mode

 - Switches from CH1 to CH2 if CH1 alarms and CH2 is good. 

Latches to CH2. Push Reset or ground Remote Reset pin to return to CH1 if it has no alarm 
or both CH1 and CH2 are in alarm.

3)  Minimum  Auto  switching,  Initial  Channel  Select  (ICS)  Mode 

- Switch stays on channel last 

selected by Manual or Remote selection after return to Auto if both channel alarms are clear or both 
channels are in alarm. Auto switching occurs only if current channel alarms and the other channel 
is clear.
Factory set mode is generally 

(1) CH1 Prime Mode.

  

When power is first applied and there are no alarms, CH1 is selected. On power loss CH2 is the selected 
channel. The Manual Select switch and contact closures to Remote Select pins (when in Auto), select CH1 or 
CH2 independent of alarms. LEDs indicate alarm and switch conditions for CH1 and CH2, REMOTE or 
MANUAL operation, and power on.  RF connectors are BNC, female. Contact closure inputs and outputs are 
via barrier strip. Dual power supplies provide redundant power to the 1582-725. The chassis is a 1 3/4” rack 
mount.

SWITCH A

MODEL 1582

POWER

1      2

   AUTO   

 CROSS TECHNOLOGIES, INC.

ON-
LINE

MANUAL 
SELECT

REM

ON-
LINE

ALM

CH 1 

CH 2

ALM

MAN

RESET

SWITCH B

   AUTO   

ON-
LINE

MANUAL 
SELECT

REM

ON-
LINE

ALM

CH 1 

CH 2

ALM

MAN

RESET

FIGURE 1.1     Model 1582-725 RF Front Panel

1582-73  BLOCK DIA

CONTROL
LOGIC SWA

AUTO

CH 1 

CH 2

SWITCH 
RESET

  1    2

 ALARM

    1      2   

REMOTE 

REMOTE 
SW. 
RESET

SWITCH A 
SWITCHED 
RF

SWITCH A 
RF 1

SWITCH A  
RF 2

CONTROL
LOGIC SWB

AUTO

CH 1 

CH 2

SWITCH 
RESET

  1    2

 ALARM

    1      2   

REMOTE 

REMOTE SW. 
RESET

FINAL OUTPUT 
SWITCH B 
SWITCHED RF

SWITCH B 
RF 1

SWITCH B  
RF 2

CH1 &CH2 
ALARM

1582-725 Block Diagram

FIGURE 1.2      Model 1582-725 RF Switch Block Diagram (

Each Switch

)

1582-725 Manual, Rev. B

 

 

  Page 3

    

          4/10/14

Summary of Contents for 1582-725













Reviews: