background image

 

 

11

 

Cromtech Generator 

Operation & Instruction Manual  

 

9.

 

FEATURES 

 

Standard Features 

 

Genuine Robin or Honda industrial engine

 

 

TG100BPE - Briggs & Stratton engine  

 

Low oil sensor

 

 

Genuine Mecc Alte Brushless Alternator

 

 

Overload protection

 

 

Australian fabricated steel frame (25mm) 

 

Australian assembled and tested 

 

2x Power outlets 

 

One-year Cromtech warranty 

 

Three-year Robin engine warranty  

 

Three-year Honda engine warranty  

 

Trade Pack Features 

 

RCBO Overload and Protection 

 

IP66 W/P Outlets 

 

Handle and Wheel Kit 

 

Lifting Hook 

10.

 

“HOW-TO” MAINTENANCE 

Maintenance is essential to give a safe and dependable service.  The following sections provide 
information on how to care for your generator properly and safely. This includes basic inspections and 
simple maintenance procedures. Other service tasks that are more difficult, or require special tools 
should be carried out by an authorised Crommelins service agent. 

WARNING

 

 

ALWAYS 

read and

 

follow the maintenance recommendations and schedules in this manual, and 

MAKE SURE

 you have the appropriate tools and skills required.

 

 

FAILURE

 to properly maintain this generator, or improper maintenance, or failing to correct a 

problem before operation, could result in a significant malfunction in which you can be seriously 

injured or killed.  

 

MAKE SURE

 the engine is stopped and cooled before starting any maintenance, servicing, or 

repair. 

NOTE: 

It is recommended to use ear protection when performing operation, maintenance, and repair 

of the generator set.

 

 

ENGINE OIL CHANGE (refer to engine instruction manual for full details) 

NOTE: 

Before changing oil, make sure there is a suitable way to dispose of the old oil. Do not pour it 

down sewage drains, onto garden soil or into open streams. Your local zoning or environmental 

regulations will give you more detailed instructions on proper disposal.

 

a.

 

For a new engine, the initial oil change should be performed after 20 hours. Thereafter, change 
oil as per the engine’s instructions manual. To change the oil, follow these steps: 

STEP 1

 

Drain oil by removing the drain plug and the oil filler cap while the engine is warm. 

Summary of Contents for TG100BPE


















Reviews: