background image

crlaurence.com  •  Toll Free (800) 421-6144  •  Fax (800) 262-3299 

CRL Glass Machinery  •  (866) 583-1377  •  Fax (866) 584-9722  Int. Phone: (773) 242-2871

CALL TOLL FREE ANYWHERE IN THE U.S. AND CANADA  •  ALL PRODUCTS F.O.B. NEAREST WAREHOUSE

CRL/SOMACA BELT SANDER

MODEL 2200RP and AU22

Page 4

ROLLER PLATEN, UPPER PULLEY, SHAFT AND BEARINGS

For ease of maintenance and durability, the Roller Platen and Top Pulley Assemblies are supplied as one-piece assemblies. Replacing the bearings or

shaft alone requires a press and an experienced operator. Because the roller platen, top crowned pulley itself, and the bearings are some of the few parts 
of the 2200RP that may need replacement, they are sold as unit assemblies. These assemblies can be replaced quickly with simple hand tools by following
the instructions on Page 3 of this manual. Assistance with any maintenance operation on the 2200RP is avaliable by calling the CRL/Sommer & Maca
Machinery Division at (866) 583-1377. Parts can be ordered online at: 

crlaurence.com

Photo 1.

Electric Water Solenoid, Valve and

Quick-Connect Fitting. Connect water supply
at “A” -1/4" NPT. Water Flow Control Valve
“H” can be used to regulate water spray.

Photo 4.

Measure Pulley to tank distance 

“D” before removing Lower Pulley.

Photo 5.

Loosen two set screws on the

Lower Pulley with a 5/32" Hex/Allen wrench.
Holes in the Pulley “E” line up with the two
set screws.

Photo 6.

Measure Pulley to bracket 

clearance “F” before removing the Roller
Platen. Loosen two Square Head screws
“G” to remove the Roller Platen.

Photo 2.

Electric Water Solenoid showing

flow direction arrow “B” on fitting.

Photo 3.

Square Head Screws “C” holding

the Upper Pulley Shaft “J”. Loosen these
to remove the Upper Pulley Assembly.

A

B

C

J

H

D

E

F

G

Summary of Contents for 2200RP















Reviews: