manualshive.com logo in svg

Critical Environment Technologies CGAS-A, Installation Manual

Share
Download
Critical Environment Technologies CGAS-A Installation Manual Download Page 13

© 2021 All rights reserved. Data subject to change without notice. 

13

Rev. B | 2021.08 

cGas Detector Analog Transmitter - Installation Manual

CERTIFICATION

Model:  CGAS-A-XXX

                S/N: CGASA1807B00010

Rating: 16-30 VDC, 3W, Class 2

              12-27 VAC, 50-60 Hz, 3VA, Class 2

CERTIFIED FOR ELECTRIC SHOCK & ELECTRICAL FIRE HAZARD ONLY. LA 

CERTIFICATION ACNOR COUVRE UNIQUEMENT LES RISQUES DE CHOC 

ELECTRIQUE ET D’INCENDIE D’ORIGINE ELECTRIQUE.
Conforms to: CSA-C22.2 No. 205-12, UL508 (Edition 18):2018

Conforms to: EMC Directive 2014/30/EU, EN 50270:2015, Type 1, EN61010

Conforms to: FCC. This device complies with part 15 of the FCC Rules, 

Operation is subject to the following two conditions: (1) This device may not 

cause harmful interference, and (2) this device must accept any interference 

received, including interference that may cause undesired operation.

Summary of Contents for CGAS-A

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands