background image

 

OPERATION INSTRUCTIONS  

 
ARMING 

To arm the alarm and lock the doors, press the Lock button on the transmitter.  You will hear a single siren chirp 
and  the  lights  will  flash  once.  The  system  will  arm,  the  doors  will  lock  and  the  starter  will  be  disabled  if  these 
optional features are installed. The red LED in the vehicle will start flashing after 5 seconds.  After a short delay 
to allow vehicle and electronics to stabilize the system will be completely armed. 
 

DISARMING 

Press the Unlock button on the transmitter to disarm the alarm.  You will hear 2 siren chirps and the lights will 
flash twice.  The LED stops flashing.  Door will unlock and dome light will turn on if the options are installed.   
 

SELECTIVE SILENT ARM / DISARM THROUGH REMOTE CONTROL 

This system can be armed and disarmed without siren chirps on an “as needed” basis. Press and release the 
Silent Button for arm/disarm without siren chirps. The alarm system can be programmed to always Silently Arm 
and Disarm with option number 1.  

 
SELECTIVE ARM / DISARM with HORN HONK (programmable) 

If  the  car  horns  are  connected  to  the  system,  they  can  be  set  up  to  chirp  (honk)  with  arm  and  disarm.  The 
default setting is to chirp with a double press of lock or unlock. This can be changed to chirp with a single press 
by option  #  3. Also the chirp pulse  duration can  be adjusted from short to long  for quiet beep to a loud  honk. 
The choices are 15, 20 and 40 milliseconds.  

 

PASSIVE ARMING MODE (Programmable) 

Passive (automatic) Arming occurs 30 seconds after the ignition is turned off and the last door is closed.  Upon 
closing  the  last  door,  the  unit  will  flash  the  lights  twice  and  LED  will  be  flashing  rapidly  to  confirm  passive 
countdown.   If a door is re-opened  within the 30-second period,  the countdown stops and begins again  when 
the door is closed.  Passive arming provides failsafe protection in case you forget to arm the system. 

 
PASSIVE ARMING with LOCK (Programmable) 

The  system  can  be  programmed  to  passively  lock  the  doors  when  the  system  passively  arms  or  rearms.  The 
default  setting  is  OFF  because  passive  locking  increases  the  risk  of  locking  the  keys  in  the  vehicle  when  the 
system arms/locks passively, without you pressing the remote. 
 

All manuals and user guides at all-guides.com

Summary of Contents for SP-302

















Reviews: