background image

 
 

EZ-90 / EZ-91

 

 

REMOTE ENGINE STARTING SYSTEM 

 

OPERATING INSTRUCTIONS 

 

INTRODUCTION 

 

**IMPORTANT NOTES:- FOR EZ-91 MODEL ONLY** 

The EZ-91 model is an add-on (expansion unit), without remotes or antenna.  It must be controlled by an existing 
alarm or keyless entry system (host system).  The “Infinity Run” feature is not available on an EZ-91 system.  Most 
of the other standard remote starting features of this system can be controlled through the existing remote of the 
host system.  For most applications, remote start is triggered by pressing a Factory remote’s Lock button 3 times 
or pressing an Auxiliary channel button on an Aftermarket system.  This is referred to in this manual as activating 
the “Green Start input wire”. 

 

*IMPORTANT INFORMATION: Primary and Optional Features

 

-PRIMARY:

  These are features that must be connected in order for the system to operate properly i.e. Remote 

Start connections, Flashing lights, Brake Reset.  For programming, the hood pin and program button are required. 

 

-OPTIONAL:

  These are features to be connected only if desired or agreed upon by the customer and the 

installing dealer i.e. Door Locks, Trunk Pop, Dome Light Illumination, Horn-Honk, Anti-Grind, etc.  These features 
may also require additional parts and/or labor fees.  Consult with your installer beforehand to be sure of what is 
going to be installed with your particular system. 

 

TECHNICAL SUPPORT: (800) 998-6880 

This device complies with FCC Rules part 15. Operation is 
subject to the following two conditions: 1) This device may not 
cause interference, and (2) this device must accept any 
interference that may be received, including interference that 
may cause undesired operation.  The manufacturer is not 
responsible for any radio or TV interference caused by 
unauthorized modification to this equipment. Such modification 
could void the user's authority to operate the equipment. 

Monday - Friday 8:00am - 4:30pm Pacific Std. Time 
Web Site: www.crimestopper.com 
E-mail: [email protected] 

 

CRIMESTOPPER SECURITY PRODUCTS, INC. 
1770 S. TAPO STREET, SIMI VALLEY, CA. 93063 

 
 

REV A - 08.2004 

 
 

Summary of Contents for Ezee Start EZ-90













Reviews: