background image

 

11 

WIRING Cont. 

 
PIN 4: BROWN/WHITE: (-) HORN CHIRP/HONK OUTPUT 

Connect to the LOW CURRENT Negative Horn Trigger wire usually located near the steering column.  If the vehicle 
horn circuit re12V, then a relay is required.  RELAY WIRING: Connect the Yellow/White wire to terminal #85, 
connect relay terminals #86 and #87 to +12V constant power. Connect terminal #30 to the +12V positive Horn 
activation wire.

 

 

PIN 5: YELLOW/BLACK: (-) IGNITION OUTPUT -or- ANTI-GRIND/STARTER DISABLE OUTPUT 

This negative output wire is programmable and can function two different ways. It can be used as a Negative Ignition 
output for GM Anti-theft and Transponder Bypass modules, or it can be programmed to function as an Anti grind/Starter 
Disable output.  As a Negative Ignition wire, this wire turns on when the remote start button is pressed and stays on 
through the duration of the remote start.  As an Anti grind/Starter disable this wire activates when the Lock button on the 
remote is pressed and during remote start.  When using this wire for an Anti grind/Starter disable, an optional Relay is 
needed to interrupt the Starter circuit.  The starter disable circuit adds an anti-theft feature to this remote start system and 
prevents accidental grinding of the starter if key is turned too far after a remote start.  See diagrams on BELOW. 
 

         YELLOW/BLACK IGNITION OUTPUT/ANTI-THEFT (Relay and/or Module not included) 

 

YELLOW/BLACK

85

86

30

87

3rd IGN 

(If  needed)

IGN SW.

OR

ANTI-THEFT/

MODULE

+12V  CONSTANT 

OR

TRANSPONDER

Diode isolate

if using both!

 

          
 
 

Summary of Contents for EZ-45DP/55DP

































Reviews: