background image

CARJACK PROTECTION 

 

ACTIVE CARJACK 

This feature provides Active Carjack protection and must be enabled before use through Alarm programming 
option (14)  See page 8.  When the Ignition is on (running), press button #2 (Trunk Symbol).  Parking lights will 
flash TWICE to confirm the Carjack countdown sequence.  90 Seconds later, the unit will begin a Carjack 
Cycle consisting of 15 seconds of pre-warning chirps turning into a full system activation with siren/flashing 
light pulses for up to 5 min.  To reset Active Carjack, IGNITION MUST BE ON, then press Button #2 again. 

 

PASSIVE CARJACK 

This feature provides Passive Carjack protection and must be enabled before use through Alarm programming 
options (13) & (14).  See page 8.  We recommend this mode should only be used in serious situations.  When 
the Ignition is on (vehicle is running), and a door is opened, the Carjack countdown sequence will be initiated.  
90 Seconds later, the unit will begin a Carjack Cycle consisting of 15 seconds of pre-warning chirps turning 
into a full system activation with siren/flashing light pulses for up to 5 min.  To reset Passive Carjack, 
IGNITION MUST BE ON AND DOORS MUST BE CLOSED, then press the override/program button (3) times. 

 

FULL-TIME CARJACK 

Use in case of extreme Carjack threat only.  This feature provides full-time Carjack protection and must be 
enabled before use through Alarm programming options (13) & (14).  See page 8.  EVERY TIME the Ignition 
is turned ON or a door is opened, then closed with the Ignition ON, a Carjack countdown sequence will be 
initiated.  90 Seconds later, the unit will begin a Carjack Cycle consisting of 15 seconds of pre-warning chirps 
turning into a full system activation with siren/flashing light pulses for up to 5 min.  You must reset the unit 
every time the IGNITION is turned on or a door is opened and closed when the ignition is on.  To reset 
IGNITION MUST BE ON AND DOORS MUST BE CLOSED, then press override/program button (3) times. 

 

NOTE:  When FULL TIME CARJACK is in effect, it must be reset every time the key is turned on, Door 
is opened, before entering VALET mode, and before Programming options or transmitters.  It is always 
in effect each time the Ignition is turned on and/or a door is opened with Ignition on. 

Summary of Contents for CS-2000


















Reviews: