GLASS DRILL InStRuctIon MAnuAL
GLASS-cHEK PRo oPERAtInG MAnuAL
crlaurence.com
c.R. Laurence co., Inc.
•
2503 E. Vernon Ave., Los Angeles, cA 90058
•
1.800.421.6144
•
crlaurence.com
SEPtEMBER 2020
P. 9
APPLICATION ExAMPLEs
The Glass-Chek PRO offers various display formats. The following illustrations are examples of measurement displays with
explanations of the application being tested and how the display format was configured.
- Measurement Example One - Double Pane Ig with Low E on Surface 2
- Measurement Example Two - Double Pane Ig with Low E on Surface 3
- Measurement Example Three - Triple Pane Ig with Low E on Surface 5
Application Examples
Page 7
The Glass-Chek ELITE offers various display formats. The following illustrations are examples of measurement displays with explanations of
the application being tested and how the display format was configured.
Display Format
• Dimensions: Inch
• Standard: Fraction
• Actual: Decimal
Display Format
• Dimensions: Inch
• Standard: Fraction
• Actual: Decimal
Display Format
• Dimensions: MM
• Standard: OFF
• Actual: ON
Display Format
• Dimensions: MM
• Standard: ON
• Actual: OFF
Resulting Measurement Displays:
Due to the application and display format, the
measurement will alternate the following three messages:
Resulting Measurement Displays:
Due to the application and display format, the
measurement will alternate the following three messages:
Resulting Measurement Displays:
Due to the application and display format, the
measurement will alternate the following 2 messages:
Resulting Measurement Displays:
Due to the application and display format, the
measurement will alternate the following two messages:
Display 1 shows fractional inches rounded to the nearest standard. Display 2 shows the actual
measurements in decimal inches. Notice how the actual measurements in 2 are slightly different than
the measurements in 1 because Display 1 shows the readings rounded to the nearest standard.
Display 3 shows that the low-E coating is on surface 2, and it indicates that the coating properties are
soft coat and have the performance of double-silver Low-E.
Display 1 shows fractional inches rounded to the nearest standard. Display 2 shows the actual
measurements in decimal inches. Display 3 shows that the meter did not detect a low-E coating on G1
or G2. Since the GC3200 only detects coatings on the first 2 panes, you may be required to test both
sides of a triple pane window to verify the presence of a low-E coating on the glass on the opposite
side of the window.
Display 1 shows the actual thickness of the window in MM. Since the “Standard” setting is set to
OFF, STANDARD dimensions are not displayed. The word “FILM” indicates suspended film between
the two panes of glass. Display 2 indicates that G1 does not have any low e coatings (“CLEAR” of
any low-E coating). In Suspended Film Mode, the GC3200 will NOT test G2 for Low E Coatings.
Display 1 shows millimeters rounded to the nearest standard. Since the “Actual” setting is set to OFF,
there is no display showing the actual dimensions of the glass - only the dimensions rounded to the
nearest standard. Display 2 shows that the low-E coating is on surface 3. Please note there are
times where the meter will not specifically designate surface 3, and may show the result as Surface 3
or 4. This means that the meter is only indicating the coating is on the second pane of glass. In that
instance, the user must test the window from the opposite side to confirm the exact low e surface.
GL
AS
S 1
GL
AS
S 1
GL
AS
S 2
GL
AS
S 2
AIR SP
ACE
AIR SP
ACE
SURF
ACE 2
SURF
ACE 3
Double Pane
Window
Triple Pane
Window
Double Pane
Window
Low-E
Low-E
Low-E
1)
1)
1)
1)
2)
2)
2)
2)
3)
3)
— Measurement Example One — Double Pane IG with Low E on Surface 2
— Measurement Example Three — Triple Pane IG with Low E on Surface 5
— Measurement Example Four — Double Pane IG with Suspended Film
— Measurement Example Two — Double Pane IG with Low E on Surface 3
GL
AS
S 1
GL
AS
S 2
AIR SP
ACE 1
AIR SP
ACE 2
GL
AS
S 3
SURF
ACE 5
Double Pane with
Suspended Film
Suspended
Film
GL
AS
S 1
AIR SP
ACE 1
AIR SP
ACE 2
GL
AS
S 2
Application Examples
Page 7
The Glass-Chek ELITE offers various display formats. The following illustrations are examples of measurement displays with explanations of
the application being tested and how the display format was configured.
Display Format
• Dimensions: Inch
• Standard: Fraction
• Actual: Decimal
Display Format
• Dimensions: Inch
• Standard: Fraction
• Actual: Decimal
Display Format
• Dimensions: MM
• Standard: OFF
• Actual: ON
Display Format
• Dimensions: MM
• Standard: ON
• Actual: OFF
Resulting Measurement Displays:
Due to the application and display format, the
measurement will alternate the following three messages:
Resulting Measurement Displays:
Due to the application and display format, the
measurement will alternate the following three messages:
Resulting Measurement Displays:
Due to the application and display format, the
measurement will alternate the following 2 messages:
Resulting Measurement Displays:
Due to the application and display format, the
measurement will alternate the following two messages:
Display 1 shows fractional inches rounded to the nearest standard. Display 2 shows the actual
measurements in decimal inches. Notice how the actual measurements in 2 are slightly different than
the measurements in 1 because Display 1 shows the readings rounded to the nearest standard.
Display 3 shows that the low-E coating is on surface 2, and it indicates that the coating properties are
soft coat and have the performance of double-silver Low-E.
Display 1 shows fractional inches rounded to the nearest standard. Display 2 shows the actual
measurements in decimal inches. Display 3 shows that the meter did not detect a low-E coating on G1
or G2. Since the GC3200 only detects coatings on the first 2 panes, you may be required to test both
sides of a triple pane window to verify the presence of a low-E coating on the glass on the opposite
side of the window.
Display 1 shows the actual thickness of the window in MM. Since the “Standard” setting is set to
OFF, STANDARD dimensions are not displayed. The word “FILM” indicates suspended film between
the two panes of glass. Display 2 indicates that G1 does not have any low e coatings (“CLEAR” of
any low-E coating). In Suspended Film Mode, the GC3200 will NOT test G2 for Low E Coatings.
Display 1 shows millimeters rounded to the nearest standard. Since the “Actual” setting is set to OFF,
there is no display showing the actual dimensions of the glass - only the dimensions rounded to the
nearest standard. Display 2 shows that the low-E coating is on surface 3. Please note there are
times where the meter will not specifically designate surface 3, and may show the result as Surface 3
or 4. This means that the meter is only indicating the coating is on the second pane of glass. In that
instance, the user must test the window from the opposite side to confirm the exact low e surface.
GL
AS
S 1
GL
AS
S 1
GL
AS
S 2
GL
AS
S 2
AIR SP
ACE
AIR SP
ACE
SURF
ACE 2
SURF
ACE 3
Double Pane
Window
Triple Pane
Window
Double Pane
Window
Low-E
Low-E
Low-E
1)
1)
1)
1)
2)
2)
2)
2)
3)
3)
— Measurement Example One — Double Pane IG with Low E on Surface 2
— Measurement Example Three — Triple Pane IG with Low E on Surface 5
— Measurement Example Four — Double Pane IG with Suspended Film
— Measurement Example Two — Double Pane IG with Low E on Surface 3
GL
AS
S 1
GL
AS
S 2
AIR SP
ACE 1
AIR SP
ACE 2
GL
AS
S 3
SURF
ACE 5
Double Pane with
Suspended Film
Suspended
Film
GL
AS
S 1
AIR SP
ACE 1
AIR SP
ACE 2
GL
AS
S 2
Application Examples
Page 7
The Glass-Chek ELITE offers various display formats. The following illustrations are examples of measurement displays with explanations of
the application being tested and how the display format was configured.
Display Format
• Dimensions: Inch
• Standard: Fraction
• Actual: Decimal
Display Format
• Dimensions: Inch
• Standard: Fraction
• Actual: Decimal
Display Format
• Dimensions: MM
• Standard: OFF
• Actual: ON
Display Format
• Dimensions: MM
• Standard: ON
• Actual: OFF
Resulting Measurement Displays:
Due to the application and display format, the
measurement will alternate the following three messages:
Resulting Measurement Displays:
Due to the application and display format, the
measurement will alternate the following three messages:
Resulting Measurement Displays:
Due to the application and display format, the
measurement will alternate the following 2 messages:
Resulting Measurement Displays:
Due to the application and display format, the
measurement will alternate the following two messages:
Display 1 shows fractional inches rounded to the nearest standard. Display 2 shows the actual
measurements in decimal inches. Notice how the actual measurements in 2 are slightly different than
the measurements in 1 because Display 1 shows the readings rounded to the nearest standard.
Display 3 shows that the low-E coating is on surface 2, and it indicates that the coating properties are
soft coat and have the performance of double-silver Low-E.
Display 1 shows fractional inches rounded to the nearest standard. Display 2 shows the actual
measurements in decimal inches. Display 3 shows that the meter did not detect a low-E coating on G1
or G2. Since the GC3200 only detects coatings on the first 2 panes, you may be required to test both
sides of a triple pane window to verify the presence of a low-E coating on the glass on the opposite
side of the window.
Display 1 shows the actual thickness of the window in MM. Since the “Standard” setting is set to
OFF, STANDARD dimensions are not displayed. The word “FILM” indicates suspended film between
the two panes of glass. Display 2 indicates that G1 does not have any low e coatings (“CLEAR” of
any low-E coating). In Suspended Film Mode, the GC3200 will NOT test G2 for Low E Coatings.
Display 1 shows millimeters rounded to the nearest standard. Since the “Actual” setting is set to OFF,
there is no display showing the actual dimensions of the glass - only the dimensions rounded to the
nearest standard. Display 2 shows that the low-E coating is on surface 3. Please note there are
times where the meter will not specifically designate surface 3, and may show the result as Surface 3
or 4. This means that the meter is only indicating the coating is on the second pane of glass. In that
instance, the user must test the window from the opposite side to confirm the exact low e surface.
GL
AS
S 1
GL
AS
S 1
GL
AS
S 2
GL
AS
S 2
AIR SP
ACE
AIR SP
ACE
SURF
ACE 2
SURF
ACE 3
Double Pane
Window
Triple Pane
Window
Double Pane
Window
Low-E
Low-E
Low-E
1)
1)
1)
1)
2)
2)
2)
2)
3)
3)
— Measurement Example One — Double Pane IG with Low E on Surface 2
— Measurement Example Three — Triple Pane IG with Low E on Surface 5
— Measurement Example Four — Double Pane IG with Suspended Film
— Measurement Example Two — Double Pane IG with Low E on Surface 3
GL
AS
S 1
GL
AS
S 2
AIR SP
ACE 1
AIR SP
ACE 2
GL
AS
S 3
SURF
ACE 5
Double Pane with
Suspended Film
Suspended
Film
GL
AS
S 1
AIR SP
ACE 1
AIR SP
ACE 2
GL
AS
S 2
Resulting Measurement Displays:
due to the application and display format, the measurement
will alternate the following three messages:
Resulting Measurement Displays:
due to the application and display format, the measurement
will alternate the following two messages:
Resulting Measurement Displays:
due to the application and display format. the
measurement will alternate the following three messages:
display 1 shows fractional inches rounded to the nearest standard. display 2 shows the actual
measurements in decimal inches. Notice how the actual measurements in 2 are slightly different than
the measurements in 1 because display 1 shows the readings rounded to the nearest standard. display
3 shows that the low-E coating is on surface 2, and it indicates that the coating properties are soft coat
and have the performance of double-silver Low-E.
Display 1 shows millimeters rounded to the nearest standard. Since the •Actual” setting Is set to
Off, there Is no display showing the actual dimensions of the glass - only the dimensions rounded
to the nearest standard. display 2 shows that the low-E coating Is on surface 3. Please note there
are times where the meter will not specifically designate surface 3, and may show the result as
surface 3 or 4. This means that the meter Is only Indicating the coating Is on the second pane of
glass. In that Instance, the user must test the window from the opposite side to confirm the exact.
low e surface.
display 1 shows fractional inches rounded to the nearest standard. display 2 shows the actual
measurements In decimal inches. display 3 shows that the meter did not detect a low-E coaling on
G1 or G2. since the GC3001 only detects coatings on the first 2 panes, you may be required to test
both sides of a triple pane window to verify the presence of a low-E coating on the glass on the
opposite side of the window.
Display format
•
dimensions: Inch
•
standard: fraction
•
Actual: decimal
Display format
• Dimensions: MM
• Standard: ON
• Actual: OFF
double Pane
Window
double Pane
Window
Triple Pane
Window
1)
2)
3)
1)
2)
3)
1)
2)
Display format
• Dimensions: Inch
• Standard: Fraction
• Actual: Decimal
