CLW-DIM1RF, DIMS1RF, & SLVD1RF(W/A/B)
Wiring Diagram for CLW-DIM1RF (L) / CLW-DIMS1RF (R)
Installation
Hot
Neutral
Load
RED
BLACK
WHITE
BLUE
Ground
GREEN
LINE
120VAC
60Hz
60Hz
120VAC
LINE
GREEN
Ground
WHITE
BLACK
RED
Load
Neutral
Hot
NOTE:
The -DIMS1RF must be installed in the same
wallbox that contains the connections to the load.
NOTE:
The -DIM1RF, -DIMS1RF, and -SLVD1RF
require a neutral wire for operation. If no neutral is
present, contact a licensed electrician for installation or
contact Crestron Customer Service for alternative wiring
options.
WARNING:
Turn off power at the circuit breaker.
Installing with power on can result in serious personal
injury and damage to the device.
NOTE:
The RED (Load) and BLACK (Hot) wires are
#14 AWG. The BLUE (Slave) and WHITE (Neutral)
wires are #18 AWG. The GREEN (Ground) wire is #16
AWG.
NOTE:
New installations should be checked for short
circuits prior to installing the -DIM1RF, -DIMS1RF, or
-SLVD1RF. With power off, close the circuit and restore
power. If the lights do not work or a breaker trips, check
and correct the wiring or fixture (if necessary). Install the
-DIM1RF, -DIMS1RF, or -SLVD1RF only when the
short is no longer present.
The warranty is void if the
-DIM1RF, -DIMS1RF, or -SLVD1RF is installed and
operated with a shorted load
.
CLW-DIMS1RF with CLW-SLVD1RF
Wiring
NOTE:
The -DIMS1RF must be installed in the same
wallbox that contains the connections to the load.
The following wiring diagram illustrates installation of
the -DIMS1RF with multiple -SLVD1RFs.
1. Turn power off at the circuit breaker.
2. If installing multiple dimmers (-DIM1RF or
-DIMS1RF), note the serial number on each
device and make sure they are being installed in
the proper location.
Wiring Diagram of CLW-DIMS1RF with multiple CLW-
SLVD1RFs
Hot
Neutral
Load
RED
CLW-DIMS1RF
BLACK
WHITE
CLW-SLVD1RF
BLUE
BLACK
BLUE
Ground
Ground
GREEN
GREEN
LINE
120VAC
60Hz
WHITE
Ground
GREEN
BLACK
BLUE
CLW-SLVD1RF
WHITE
3. Wire the device for the appropriate application.
Choose either “CLW-DIM1RF / CLW-
DIMS1RF Wiring” or “CLW-DIMS1RF with
CLW-SLVD1RF Wiring”, shown on this page
and the following page.
NOTE:
Alternative wiring methods can be obtained from
the Dealer/Tech Resources | Design Center section of the
Crestron website (http://www.crestron.com/dealer-
tech_resources/design_center/hot_design_tips_and_
diagrams/tech_sales_tips/).
NOTE:
Do not connect the BLUE (Slave) wire to the
Black (Hot) or RED (Load) wires.
CLW-DIM1RF / CLW-DIMS1RF Wiring
NOTE:
The RED (Load) and BLACK (Hot) wires are
#14 AWG. The BLUE (Slave) and WHITE (Neutral)
wires are #18 AWG. The GREEN (Ground) wire is #16
AWG.
NOTE:
The -DIM1RF and -DIMS1RF require a neutral
wire for operation. If no neutral is present, contact a
licensed electrician for installation or contact Crestron
customer service for alternative wiring options.
NOTE:
If a -DIMS1RF is installed without a
-SLVD1RF, the BLUE lead (Slave) should be capped.
The following wiring diagram illustrates installation of
the -DIM1RF or -DIMS1RF.
4. Push all Class 1 power wires back into the
wallbox and fasten the device to the wallbox
with the provided screws.
5. Attach decorative faceplate.
6. Restore
power.
4
•
Stand Alone Wall Box Dimmer : CLW-DIM1RF, DIMS1RF, & SLVD1RF
Installation Guide – DOC. 6292