background image

12  |  

©  CRESTO  Smartline  X  |  EDITION  001/2017-­10-­02  |  UK  version  (Master)

  

  

  

  

  

  

Fig.  6  

  

8.

  

The  speed  of  the  descent  is  regulated  with  one  hand  on  the  handle  and  the  other  hand  
holding  the  line  below  the  device.  Start  with  the  line  at  an  angle  out  of  the  slot.  With  the  
descender  upside  down,  the  descent  starts  by  pulling  the  handle  upwards  

Fig.7

,  and  

stops  when  moving  the  handle  downwards  or  by  releasing  it.  Increase  or  decrease  
friction  by  moving  the  line  into  the  narrow  part  of  the  slot  or  away  as  shown  in  

Fig.3:B  

and  3:C

.  It  is  important  to  always  keep  one  hand  on  the  line  below  the  device  to  have  

better  control  of  the  descent

 

  

Fig.  7  

 

9.

  

Ensure  that  the  descent  is  not  in  conflict  with  moveable  machinery,  obstacles  or  live  
cable.  The  line  must  not  lie  over  sharp  edges.

 

10.

   Once  the  person  is  safely  on  the  ground,  give  necessary  medical  assistance  and  call  

for  help.  Detach  the  rope  from  the  harness.

 

 

 

Summary of Contents for RESQ Smartline X
























Reviews: