5925 Heisley Road • Mentor, OH 44060-1833
Phone: 877/CRESCOR • Fax: 440/350-7267
www.crescor.com
© Crescent Metal Products, Inc. 1998 All rights reserved.
Litho in U.S.A.
®
CO-151-FPW-UA-12B-Q1
In line with its policy to continually improve its products,
CRES COR reserves the right to change materials and
specifications without notice.
SHORT FORM SPECIFICATIONS
Cres Cor Pass-Thru AquaTemp Roast-N-Hold Convection
Oven Model CO-151-FPW-UA-12B-Q1. Removable power
unit 20 ga. 304 stainless steel, recessed control panel. Two
stainless steel probes, 1-1/2 and 6” long. Cabinet 22 ga. 304
stainless steel. Stainless steel internal frame; coved corner
interior. Dutch doors front and back, 22 ga. 304 stainless
steel, ceramic magnetic latch, heavy duty hinges. 16 ga.
stainless steel water reservoir, 4 gallon capacity. Fiberglass
insulation in sides 2”; back, doors and base 1-1/2”. (12) sets
universal angles for multiple pan sizes and spacing. One
piece base .125 aluminum. 5" swivel modulus casters,
Delrin bearings. Load capacity 250 lbs. each. 8200 Watts,
Volts, 60 Hz.,
Phase. 2 year parts warranty. Provide
the following accessories:
__ . UL, CUL, UL
Sanitation listed.
CABINET:
• Body: 22 ga. 304 stainless steel.
• Reinforcement: Internal framework of 16 ga. stainless steel.
• Insulation: Fiberglass, thermal conductivity (K factor) is .23
•
at 75˚F. 1-1/2" in back wall, doors, base; 2" in side walls.
• Water pan: 4 Gallons; 16 ga. stainless steel with 1850 Watt
•
heater and with petcock drain; mounted to base.
• Drip trough: Formed 18 ga. stainless steel; mounted to lower
front and rear of cabinet; removable drip pan.
• Air tunnels (2): 20 ga. stainless steel, lift-out type, mounted
•
on side walls.
• Push/pull handles (4): 7" vertical; recessed.
BASE:
• One piece construction, .125 aluminum.
• Casters: 5" dia., swivel, modulus tires, 1-1/4 wide, load cap.
•
250 lbs. each, temp. range -45˚/+180˚F. Delrin bearings. Front
casters equipped with brakes.
DUTCH DOORS:
• Field reversible.
• Formed 22 ga. 304 stainless steel.
• Latches: Chrome plated zinc with composite handle, ceramic
•
magnetic type; mounted inboard.
• Hinges: Heavy duty chrome plated zinc, mounted inboard.
• Gaskets: Perimeter type, silicone.
• Pan stops: Embossed.
PAN SLIDES:
• Stainless steel wire universal angles (.306 dia.) mounted on
•
lift-out posts.
• 12 sets of angles adjustable on 1-1/2" centers.
• Grids (6): Nickel chrome plated steel, raised wire 17" x 25".
POWER REQUIREMENTS AVAILABLE:
• 8200 Watts, 208 Volts, 60 Hz., 1 phase, 39 Amps.,
•
50 Amp. service.
• 8200 Watts, 240 Volts, 60 Hz., 1 phase, 34 Amps.,
•
50 Amp. service.
• 8200 Watts, 208 Volts, 60 Hz., 3 phase, 23 Amps.,
•
30 Amp. service.
• 8200 Watts, 240 Volts, 60 Hz., 3 phase, 20 Amps.,
•
30 Amp. service.
POWER UNIT COMPONENTS: (refer to above drawing)
• Body:Formed 304 stainless steel with black control panel, recessed
and tilted 7˚.
A) Ther mostat (microprocessor)
• Holding up to 250˚F (121˚C)
• Cook/Retherm up to 350˚F(176.5˚C)
• Thermometer
B) Thermostat (humidity): Solid state
C) Switch: Lighted ON-OFF rocker type.
D) Pilot light for low water level.
• Power cord:Permanent, 8ft., 6/3 ga.with right angle plug.
• Air heaters (3): 2670 Watts each.
• Water heater: 1850 Watts.
• Blower motors (3).
• Vent fans (2).
• Fuses (2): 3 amp.
• Probes (2): 1-1/2” and 6”, stainless steel.
INSTALLATION REQUIREMENTS:
• Check local vent hood codes for mobile Roast-N-Hold ovens.
CRES COR
PAN
DIM “A”
DIM “B”
DIM “C”
INSIDE DIMENSIONS
WEIGHT
MODEL NO.
CAP/ANGLES
SIZE
WIDTH
DEPTH
HEIGHT
WIDTH
DEPTH
HEIGHT
ACT.
12
SEE NOTE
IN
28-3/4
37-3/4
73-1/2
21-1/4
26-1/2
58
LBS
403
CO-151-FPW-UA-12B-Q1
SETS
BELOW
MM
740
960
1870
540
675
1475
KG
183
NOTE: Refer to pan size chart at end of section.
ALL CONSTRUCTION IS RIVETED, WELDED AND FINISHED.
DETAIL OF
PAN SLIDE
