4 of 8
LPN00631X0001A0_B
8
STEP 11:
Remove the nut from the threaded nipple of
the photocell and insert the threaded nipple
of the photocell through the hole in the cover.
The body of the photocell and the o-ring on
the threaded nipple should remain on the
inside surface of the cover.
STEP 12:
Tighten the nut onto the exposed end of the
threaded nipple to secure the photocell to the
cover.
STEP 13:
Wire the photocell by following the wiring
instructions included with the photocell.
STEP 14:
Connect supply ground lead to luminaire
ground lead.
STEP 15:
Replace the wiring compartment cover that
was removed in Step 3. Tighten screws to 30
in-lbs (3.5 N
·
m).
ADJUSTABLE ARM MOUNT WITH TWIST-LOCK PHOTOCELL- REQUIRES USE OF
NTX-AA-3R ACCESSORY AND TWIST-LOCK PHOTOCELL
NOTE:
Area lights are only designed for
mounting orientation from 0° (horizontal) to
45° tilt.
NOTE:
Area lights are not to be used as
uplights.
STEP 1:
Plug the female end of the quick connect,
supplied with the trunnion, into the male
connector on the luminaire. Make sure the two
halves lock together. See
Figure 1.
STEP 2:
Position luminaire to be assembled to
adjustable arm face down with mounting holes
facing towards you.
IMPORTANT:
Adjustable arm with Twist Lock
Photocell must be mounted with twist lock
receptacle on the right side of the adjustable
arm as viewed from behind luminaire.
STEP 3:
Align the four holes in the upper adjustable
arm with the four tapped holes in the
luminaire housing. Attach the adjustable
arm to the luminaire using the (4) 5/16” (8
mm) bolts and lockwashers supplied with the
adjustable arm kit. Tighten bolts to 132 in-lbs
(15 N
·
m). See
Figure 8.
STEP 4:
Remove wiring compartment cover on
adjustable arm by removing (2) screws. See
Figure 8.
STEP 5:
Feed supply leads up through the tenon that
the luminaire will be mounted on.
STEP 6:
Route supply leads through open end of the
adjustable arm and into wiring compartment.
NOTE:
It may be necessary to disassemble
the upper and lower portions of the adjustable
arm in order to run the leads into the wiring
compartment. If disassembly is necessary,
remove the 3/8” (10 mm) bolt and lockwasher
inside the wiring compartment and route
leads into wiring compartment. See
Figure 8.
Reassemble upper and lower arm
halves and replace 3/8” bolt and lockwasher.
Do not tighten bolt at this time.
STEP 7:
Strain relief is required for electrical
connections on slip fitter mounts at heights of
25’ (7.6 m) and above. Tie a knot in the supply
leads above the hole where the leads enter
the wiring chamber to reduce the strain on
the connections. Make sure knot will not slip
through opening in wiring compartment.
STEP 8:
Slip lower adjustable arm over 2 -3
/
8” (60
mm) O.D. heavy wall pipe or tenon making
sure not to pinch any leads. Aim the luminaire
in the proper direction and hand tighten all
four Allen head set screws against outer
wall of tenon. Once all four screws are hand
tightened, secure them by tightening them to
140 in-lbs (16 N
·
m).
STEP 9:
If 3/8” bolt holding the two halves of the
adjustable arm together was not loosened in
Step 6, loosen the bolt (DO NOT remove it) at
this time.
STEP 6:
Strain relief is required for electrical connections on slip
fitter mounts at heights of 25’ (7.6 m) and above. Tie a knot
in the supply leads above the hole where the leads enter
the wiring chamber to reduce the strain on the connections.
Make sure knot will not slip through opening in wiring
compartment.
STEP 7:
Slip lower adjustable arm over 2 -3
/
8” (60 mm) O.D. heavy
wall pipe or tenon making sure not to pinch any leads. Aim
the luminaire in the proper direction and hand tighten all four
Allen head set screws against outer wall of tenon. Once all
four screws are hand tightened, secure them by tightening
them to 140 in-lbs (16 N
·
m).
STEP 8:
If 3/8” bolt holding the two halves of the adjustable arm
together was not loosened in Step 5, loosen the bolt (DO NOT
remove it) at this time.
STEP 9:
Tilt the luminaire to the desired angle and tighten the 3/8”
(10 mm) bolt to 19 ft-lbs (25 N
·
m) to lock the adjustable arm
in place.
STEP 10:
Remove the center knockout form the wiring compartment
cover by striking knockout with a punch and hammer.
Remove the Bolt at
the Center Inside
the Cover Plate to
Separate the Two
Halves
(2) Screws for
Removal of Wiring
Compartment
Cover
Tighten the Screws
Here to Fix the
Adjustable Arm on
the Pole
Lower Half of the
Arm to be Fixed on
the Mounting Pole
Upper Arm to be
Fixed on to the
Luminaire Head
using (4) bolts
Twist Lock
Photocell
Receptacle
Supply Leads
