,QGXVWU\&DQDGD1RWLFH
The Industry Canada label identifies certified equipment. This
certification means that the equipment meets certain protective,
operational, and safety requirements of telecommunications network.
The Department does not guarantee the equipment will operate to the
user’s satisfaction.
Before installing this equipment, users should ensure that it is
permissible to be connected to the facilities of the local
telecommunications company. The equipment must also be installed
using an acceptable method of connection. The customer should be
aware that compliance with the above conditions may not prevent
degradation of service in some situations.
Repairs to certified equipment should be made by an authorized
Canadian maintenance facility designated by the supplier. Any
repairs or alterations made by the user to this equipment, or equipment
malfunctions, may give the telecommunications company cause to
request the user to disconnect the equipment.
For their own protection, users should ensure that the electrical
ground connections of the power utility, telephone lines and internal
metallic water pipe system, if present, are connected together. This
precaution may be particularly important in rural areas.
CAUTION: Users should not attempt to make such connections
themselves, but should contact the appropriate electric inspection
authority, or electrician, as appropriate.
1RWLFH
The Load Number (LN) assigned to each terminal device denotes the
percentage of the total load to be connected to a telephone loop which
is used by the device, to prevent overloading. The termination on a
loop may consist of any combination of devices subject only to the
requirement that the sum of the Load Numbers of all devices does not
exceed 100.
/·eWLTXHWWHGX0LQLVWqUHGHV
,QGXVWULHVGX&DQDGD
L’Étiquette du Ministère des Industries du Canada identifie le matériel
homologué. Cette étiquette certifie que le matériel est conforme à
certaines normes de protection, d’exploitation et de sécurité des
réseaux de télécommunications. Le Ministère n’assure toutefois pas
que le matériel fonctionnera à la satisfaction de l’utilisateur. Avant
d’installer ce matériel, l’utilisateur doit s’assurer qu’il est permis de
le raccorder aux installations de l’entreprise locale de
télécommunication. Le matériel doit également être installé en
suivant une méthode acceptée de raccordement. L’abonné ne doit pas
oublier qu’il est possible que la conformité aux conditions énoncées
ci-dessus n’empêche pas la dégradation du service dans certaines
situations. Les réparations de matériel homologué doivent être
effectuées par un centre d’entretien canadien autorisé désigné par le
fournisseur. La compagnie de télécommunications peut demander à
l’utilisateur de débrancher un appareil à la suite de réparations ou de
modifications effectuées par l’utilisateur ou à cause de mauvais
fonctionnement. Pour sa propre protection, l’utilisateur doit s’assurer
que tous les fils de mise à la terre de la source d’énergie électrique,
des lignes téléphoniques et des canalizations d’eau métalliques, s’il y
en a, sont raccordé ensemble. Cette précaution est particulièrement
importante dans les régions rurales.
AVERTISSEMENT: L’utilisateur ne doit pas tenter de faire ces
raccordements lui-même; il doit avoir recours à un service
d’inspection des installations électriques, ou à un électricien, selon le
cas.
$YLV
L’indice de charge (IC) assigné à chaque dispositif terminal indique,
pour éviter toute surcharge, le pourcentage de la charge totale qui peut
être raccordê à un circuit têlêphonique bouclê utilisê par ce dispositif.
La terminaison du circuit bouclé peut être constituée de n’importe
quelle combinaison de dispositifs, pourvu que la somme des indices
de charge de l’ensemble des dispositifs ne dépasse pas 100.
mb5625.book Page v Tuesday, October 19, 1999 2:41 PM
Summary of Contents for Modem Blaster V.90 External
