Creative 3D Blaster Annihilator 2 MX GB0030 Installation Manual Download

Page: 21 / 22

! , : %

+ 3%- :

$32$'23$&

- 9 - %

3 =

3&#,'$>'2$'&2$ 2'$ #2&

)! - P3

%P!- %<

% - 5%75 75 78 $ &

!H2H" %2 !

P !3 %

3P!:3; - )

2$%2$E>%3%23$'$

$,#! G

26(

3 ' =

-8

! 1"

#''$%(

$ ) % 33

3 . !

-%::

P! %- $ ) -%

! 5::-

=7$ )

% 3

3% 3- 3 !

- ) - %%

-- < 3 - %

:=- - %3

-
0+ )3 -

%-0+ 3 -

ADDENDUM TO THE MICROSOFT SOFTWARE LICENSE
AGREEMENT (WINDOWS 95)

IMPORTANT: By using the Microsoft software files (the “Microsoft Software”)
provided with this Addendum, you are agreeing to be bound by the following terms.
If you do not agree to be bound by these terms, you may not use the Microsoft
Software.

The Microsoft Software is provided for the sole purpose of replacing the
corresponding files provided with a previously licensed copy of the Microsoft
software product identified above (“ORIGINAL PRODUCT”). Upon installation,
the Microsoft Software files become part of the ORIGINAL PRODUCT and are
subject to the same warranty and license terms and conditions as the ORIGINAL
PRODUCT. If you do not have a valid license to use the ORIGINAL PRODUCT,
you may not use the Microsoft Software. Any other use of the Microsoft Software
is prohibited.

SPECIAL PROVISIONS APPLICABLE TO THE EUROPEAN UNION

IF YOU ACQUIRED THE SOFTWARE IN THE EUROPEAN UNION (EU), THE
FOLLOWING PROVISIONS ALSO APPLY TO YOU. IF THERE IS ANY
INCONSISTENCY BETWEEN THE TERMS OF THE SOFTWARE LICENSE
AGREEMENT SET OUT EARLIER AND IN THE FOLLOWING PROVISIONS,
THE FOLLOWING PROVISIONS SHALL TAKE PRECEDENCE.

DECOMPILATION
You agree not for any purpose to transmit the Software or display the Software’s
object code on any computer screen or to make any hard copy memory dumps of the
Software’s object code. If you believe you require information related to the
interoperability of the Software with other programs, you shall not decompile or
disassemble the Software

to obtain such information, and you agree to request such information from Creative
at the address listed earlier. Upon receiving such a request, Creative shall determine
whether you require such information for a legitimate purpose and, if so, Creative
will provide such information to you within a reasonable time and on reasonable
conditions.

LIMITED WARRANTY
EXCEPT AS STATED EARLIER IN THIS AGREEMENT, AND AS
PROVIDED UNDER THE HEADING “STATUTORY RIGHTS”, THE
SOFTWARE IS PROVIDED AS-IS WITHOUT WARRANTY OF ANY
KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT
LIMITED TO, ANY IMPLIED WARRANTIES OR CONDITIONS OF
MERCHANTABILITY, QUALITY AND FITNESS FOR A PARTICULAR
PURPOSE.

LIMITATION OF REMEDY AND DAMAGES
THE LIMITATIONS OF REMEDIES AND DAMAGES IN THE SOFTWARE
LICENSE AGREEMENT SHALL NOT APPLY TO PERSONAL INJURY
(INCLUDING DEATH) TO ANY PERSON CAUSED BY CREATIVE’S
NEGLIGENCE AND ARE SUBJECT TO THE PROVISION SET OUT
UNDER THE HEADING “STATUTORY RIGHTS”.

STATUTORY RIGHTS
Irish law provides that certain conditions and warranties may be implied in contracts
for the sale of goods and in contracts for the supply of services. Such conditions and
warranties are hereby excluded, to the extent such exclusion, in the context of this
transaction, is lawful under Irish law. Conversely, such conditions and warranties,
insofar as they may not be lawfully excluded, shall apply.

Accordingly nothing in this Agreement shall prejudice any rights that you may
enjoy by virtue of Sections 12, 13, 14 or 15 of the Irish Sale of Goods Act 1893 (as
amended).

GENERAL
This Agreement is governed by the laws of the Republic of Ireland. The local
language version of this agreement shall apply to Software acquired in the EU. This
Agreement is the entire agreement between us, and you agree that Creative will not
have any liability for any untrue statement or representation made by it, its agents or
anyone else (whether innocently or negligently) upon which you relied upon
entering this Agreement, unless such untrue statement or representation was made
fraudulently.

Safety & Regulatory Information

The following sections contain notices for various countries:

CAUTION: This device is intended to be connected by the user to a CSA/TUV/UL
certified/listed IBM AT or compatible personal computers in the manufacturer’s
defined operator access area. Check the equipment operating/installation manual
and/or with the equipment manufacturer to verify/confirm if your equipment is
suitable for devices to be connected to it.

ATTENTION: Ce périphérique est destiné à être connecté par l’utilisateur à un
ordinateur IBM AT certifié ou listé CSA/TUV/UL ou compatible, à l’intérieur de la
zone d'accès définie par le fabricant. Consulter le mode d’emploi/guide
d'installation et/ou le fabricant de l’appareil pour vérifier ou confirmer qu'il est
possible de connecter d'autres périphériques à votre sytème.

Notice for the USA

FCC Part 15: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, this notice is
not a guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try
one or more of the following measures:

❑

Reorient or relocate the receiving antenna.

❑

Increase the distance between the equipment and receiver.

❑

Connect the equipment to an outlet on a circuit different from that to which the
receiver is connected.

❑

Consult the dealer or an experienced radio/TV technician.

❑

Caution

To comply with the limits for the Class B digital device, pursuant to Part 15 of the
FCC Rules, this device must be installed in computer equipment certified to comply
with the Class B limits.

All cables used to connect the computer and peripherals must be shielded and
grounded. Operation with non-certified computers or non-shielded cables may
result in interference to radio or television reception.

Modifications

Any changes or modifications not expressly approved by the grantee of this device
could void the user’s authority to operate the device.

Notice for Canada

This apparatus complies with the Class “B” limits for radio interference as specified
in the Canadian Department of Communications Radio Interference Regulations.

Cet appareil est conforme aux normes de CLASSE “B” d’interférence radio tel que
spécifié par le Ministère Canadien des Communications dans les règlements
d’interférence radio.

Compliance

This product conforms to the following Council Directive:
Directive 89/336/EEC, 92/31/EEC (EMC), 73/23/EEC (LVD)

Declaration of Conformity

According to the FCC96 208 and ET95-19 documents,

Name:

Creative Labs Inc.

Address:

1901 McCarthy Boulevard
Milpitas, CA. 95035
United States
Tel: (408) 428-6600

declares under its sole responsibility that the product

Trade Name:

Creative Labs

Model Number: GB0030 (AGP version)