Creative Playthings Williamsburg Assembly Manual Download

Page: 1 / 20

Model #SH 3200-000

ASSeMbly MAnuAl

williAMSburg

Please read the owner’s manual before assembling your play set.

it provides additional information on the care and use of your play

set. you must carefully read the entire instruction manual before pro-

ceeding with the assembly or use of your new play set.

Creative Playthings takes great care to design its products with

your child’s safety in mind. However, only with careful supervision

and proper safety instructions, can you be assured of safe play time

on any product designed for children.

witH tent

roof

this product is intended for single family home/residential use

only and not intended for use in any public setting. Placement in

any public setting constitutes a misuse of this product.

Summary of Contents for Williamsburg




















Search results

Summary of Contents for Williamsburg

Reviews:

Related manuals for Williamsburg

Brands by name

Popular brands

Creative Playthings Williamsburg, Assembly Manual

Search results

Summary of Contents for Williamsburg

Reviews:

Related manuals for Williamsburg

Brands by name

Popular brands