background image

Assembly instructions

© Copyright 2017, Creative Playthings, printed in U.S.A.

DiRECT ADAPTER FOR SPiRAL & SWOOSH SLiDES
19946-100 Rev B (07-17)

page 2

E-(3) Bottom Elbow

  P/N 15064-1476-Green

B-(1) Left Entrance

  P/N 15064-1475-Green

G-(1) Run-off Section

  P/N 15064-1479-Green

H-(1) Lower Slide Support Bracket

  P/N 15064-1120

i-(2) Spiral Slide Anchor Nail

   P/N 12100-848

A-(1) Mounting Plate

  P/N 15064-1480-Green

C-(1) Right Entrance

  P/N 15064-1474-Green

D-(2) Top Elbow

  P/N 15064-1477-Green

F-(1) Exit Section

  P/N 15064-1478-Green

50567-700   hardware, Direct connect

 37  12002-206  Flat Washer 5/16"

 23  12017-206  Lock Washer 5/16"

 23  17001-105  Weld Nut 5/16"
 2  17003-611  Hex Bolt 5/16 x 1-1/2"

 2  17003-811  Hex Bolt 5/16 x 2"

 13  17003-1611  Hex Bolt 5/16 x 4"

 6  17003-1811  Hex Bolt 5/16 x 4-1/2"

 4  17003-2011  Hex Bolt 5/16 x 5"

 4  17036-602  Lag Screw 5/16 x 1-1/2"

 6  17036-1002  Lag Screw 5/16 x 2-1/2"

 2  17036-1202  Lag Screw 5/16 x 3"
 38  17020-106  Screw #8 x 1-5/8"

 28  17020-109  Screw #8 x 2-1/2"

 5  17120-902  Self-Drilling Screw 2-1/2"
 4  12002-203  Flat Washer 1/4"

 3  17001-104  Weld Nut, 1/4"

 4  17036-601  Lag Screw 1/4 x 1-1/2"

 3  17119-409  Truss Head Bolt 1/4 x 1"
 17  15081-704  1" Hole Cap, Brown

spiral slide hardware (in sp. slide box)

 106  17003-311  5/16 x 3/4" Hex Bolts

 212  12002-206  5/16 Flat Washers

 106  12052-206  5/16" Lock Nuts

screw  #8 x 2-1/2"

flat washer 5/16"

lock washer 5/16"

weld nut 5/16"

lock nut 5/16"

5/16 x 4" hex bolt

hole cap

5/16 x 1-1/2" hex bolt

5/16 x 3/4" hex bolt

5/16 x 2" hex bolt

5/16 x 4-1/2" hex bolt

5/16 x 5" hex bolt

5/16 x 3" lag screw

5/16 x 2-1/2" lag screw

5/16 x 1-1/2" lag screw

#8 x 1-5/8" screw

#10 x 2-1/2" self-Drill screw

flat washer 1/4"

weld nut 1/4"

1/4 x 1-1/2" lag screw

1/4 x 1" truss head bolt

slide components

fasteners

Summary of Contents for 63091-111












Reviews: