background image

6" & 8" Bear Cat Chipper Operator’s Manual

II

Limited Warranty

Crary Bear Cat chippers are warranted for 1 year from date of sale for consumers , commercial, or rental

operations.

Within the above stated period, Crary Co. will replace any part(s) found to be defective in material and/or

workmanship, after the receipt of the part in our plant.  Labor costs to replace these defective parts will be

paid at a Crary established labor rate and time allowed (flat rate) for repair.  All transportation charges

incurred in shipping part(s) are the responsibility of the purchaser.

This warranty is void in the case of accidents, failure to perform normal maintenance, or failure to follow

those instructions listed in the service manual.  This warranty is also in lieu of all other expressed warranties

and voids any implied warranty as to the merchantability or fitness of the product for a particular purpose

and of any other obligation on the part of Crary Co.  Some states do not allow limitations on how long the

implied warranty lasts, so the above limitation may not apply to you.

This warranty applies only to parts or components that are defective, and does not cover necessary repair

due to normal wear, misuse, accidents, or lack of proper maintenance.  This includes belts, pulleys, and

chipper blades. Regular routine maintenance of the unit to keep it in proper operating condition is the

responsibility of the owner.

All warranty repair reimbursable under the Crary Co. warranty must be performed by an authorized Bear

Cat service dealer using Bear Cat approved replacement parts.  Repair or attempted repair by anyone other

than an authorized Bear Cat service dealer is not reimbursable under the Crary Co. warranty.  In addition,

these unauthorized repair attempts may result in additional malfunction, the correction of which is not

covered by warranty.

Crary Co. is not liable for indirect, incidental, or consequential damages in connection with the use of this

product including any cost or expense or providing substitute equipment or service during periods of

malfunction or non-use.

Some states do not allow the exclusion of incidental or consequential damages, so the above exclusion

may not apply to you.  This warranty gives you specific legal rights.  You may also have other rights that

vary from state to state.

Be sure to note the serial number in any correspondence with Crary Co. or any authorized Bear Cat dealer.

Crary Company

A Division of TerraMarc Industries

237 12th St. NW  •  P.O. Box 849

West Fargo, ND 58078-0849

(701)282-5520 • FAX: (701)282-9522

www.bearcatproducts.com

www.terramarc.com

Summary of Contents for 71620


























Reviews: