Crane IQVu Operator'S Manual Download Page 24 | Manualshive

Page: 24 / 64

background image

24

Tap on required Job to
start taking readings

Tap to add IS
transducer

IQVu is compatible with Checkstar Multi, UTA and IS transducers. Multiple transducers can be attached via

The optional Automatic Switch Box.

GREEN

= Available AND selected

AMBER

= Available NOT selected

RED

= NOT available

Connected transducers are colour coded.

“Plug and Play” transducer will automatically appear in the

List when the refresh icon is tapped.

When using the optional automatic switch box, IS transducers can ONLY be in port 1

TRANSDUCERS

«
...
22
23
24
25
26
...
»

Summary of Contents for IQVu

































































Reviews:

No comments

Related manuals for IQVu

Brand: MadgeTech Pages: 10

Brand: MadgeTech Pages: 12

Brand: MadgeTech Pages: 16

Brand: MadgeTech Pages: 4

Brand: SS Telecoms Pages: 16

Brand: Cortalk Pages: 26

Evolution EVRC5002

Brand: Vanco Pages: 12

Brand: Geomatics Pages: 16

Brand: Acksen Pages: 2

Brand: Campbell Pages: 48

Apollo IV DT304

Brand: UEi Pages: 20

Brand: ICP DAS USA Pages: 8

Brand: RBR Pages: 27

Brand: EasyLog Pages: 6

Brand: PASCO Pages: 13

Brand: Sutron Pages: 22

Brand: Sea-Bird Scientific Pages: 87

AUTOID 6 Series

Brand: Seuic Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands