Crane IQVu Operator'S Manual Download | Manualshive

Page: 14 / 64

background image

14

Connect the lead from the PSU to the connector on the bottom of the IQVu (see below), and connect the PSU to an AC
mains supply. The adaptor can be used for direct power from the mains or to charge the internal battery. It has an auto-
matic cut-off to prevent overcharging.

Ensure suitable PC software and drivers are installed before connecting IQVu
Connect the Micro USB cable to the Micro USB Host connector, then connect to USB socket on PC.
Refer to PC software manual for further information.

CAUTION : To ensure optimal performance from the battery use only included AC PSU. Do not charge the
battery when the temperature is at extremes (i.e >40 deg C {104 deg F} OR < 0 deg C {32 deg F})
If the IQVu is not used for a long period of time, ensure the battery is charged at least once every 2 weeks.
Over discharge can adversely effect performance.

CONNECTING CHARGER

CONNECTING TO PC

Whilst charging, the bottom right corner of the IQVu display may become warm. This is within normal

operating parameters and is not harmful to the device.

«
...
12
13
14
15
16
...
»

Summary of Contents for IQVu

































































Reviews:

No comments

Related manuals for IQVu

Brand: EasyLog Pages: 2

Brand: Mobii Pages: 8

Brand: Dataq Instruments Pages: 32

Brand: Lambrecht Pages: 30

Brand: Racelogic Pages: 46

706581/18-321-33/020,444

Brand: JUMO Pages: 48

Brand: Rand McNally Pages: 7

SmartSystem SHIP L

Brand: berlinger Pages: 26

Brand: berlinger Pages: 40

Brand: Extech Instruments Pages: 39

Brand: Novus Pages: 6

Brand: Novus Pages: 7

Brand: Dostmann Electronic Pages: 17

Brand: Data Harvest Pages: 40

Brand: Xetron Pages: 2

Brand: Omega Pages: 43

Bently Nevada SCOUT200 Series

Brand: GE Pages: 6

Brand: NexSens Technology Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands