Crane Barnes SF411 Series Installation Manual Download Page 4

Page: 4 / 20

DISCHARGE .......................

2” NPT, Female, Vertical

LIQUID TEMP .....................

77°F (25°C) Continuous

MOTOR HOUSING .............

Cast Iron ASTM A-48, Class 30

VOLUTE ..............................

Cast Iron ASTM A-48, Class 30

SEAL PLATE ......................

Cast Iron ASTM A-48, Class 30

IMPELLER:

Design ............

2-vane, Open with Pump Out Vanes on

Back Side. Dynamically Balanced,

ISO

G6.3

Material ...........

Cast Iron ASTM A-48, Class 30

SHAFT .................................

416 Stainless Steel

O-RINGS .............................

Buna-N

HARDWARE .......................

300 Series Stainless Steel

PAINT ..................................

Air dry enamel

SEAL

Design .............

Single Mechanical, Oil Filled reservoir

Secondary Exclusion Seal

Material ...........

Carbon/Ceramic/Buna-N

Hardware - 300 series stainless steel

CORD ENTRY .....................

15 Ft. (5m) Quick disconnect cord

with plug on 115 volt, pressure

gromment for sealing and strain relief.

UPPER BEARING:

Design .............

Single Row, Ball, Oil Lubricated

Load ................

Radial

LOWER BEARING:

Design .............

Single Row, Ball, Oil Lubricated

Load ................

Radial & Thrust

MOTOR:

Design .............

NEMA L Torque Curve. Oil Filled

Squirrel Cage Induction

Insulation ........

Class B

SINGLE PHASE ..................

Permanent Split Capacitor (PSC)

Includes

Thermal

Overload

Protection in motor

OPTIONAL EQUIPMENT ....

Seal Material, Additional Cord

PUMP SPECIFICATIONS SERIES:

IMPORTANT !

1.)

DO NOT USE TO PUMP FLAMMABLE LIQUIDS

2.) NSTALLATIONS SUCH AS DECORATIVE FOUNTAINS OR WATER FEATURES PROVIDED FOR VISUAL ENJOYMENT MUST BE INSTALLED

IN ACCORDANCE WITH THE NATIONAL ELECTRIC CODE ANSI/NFPA 70 AND/OR THE AUTHORITY HAVING JURISDICTION. THIS PUMP IS

NOT INTENDED FOR USE IN SWIMMING POOLS, RECREATIONAL WATER PARKS, OR INSTALLATIONS IN WHICH HUMAN CONTACT

WITH PUMPED MEDIA IS A COMMON OCCURRENCE.

inches

(mm)

Summary of Contents for Barnes SF411 Series





















Search results

Summary of Contents for Barnes SF411 Series

Reviews:

Related manuals for Barnes SF411 Series

Brands by name

Popular brands

Crane Barnes SF411 Series, Installation Manual

Search results

Summary of Contents for Barnes SF411 Series

Reviews:

Related manuals for Barnes SF411 Series

Brands by name

Popular brands