manualshive.com logo in svg

cramZ 900-R, Installation Manual

Share
Download
cramZ 900-R Installation Manual Download Page 19

 

In

fo

rm

ation

 su

b

je

cts

 to

 c

ha

ng

e 

w

itho

ut

 n

o

ti

ce

. 

 

 

9    FCC Compliance 

900-R Installation  Manual

 

•   This device has been authorized by the FCC Rules and Industry Canada. 

 

•  This device complies with the limits for a Class B digital and Class B intentional radiator, 

pursuant to Part 15 of FCC Rules and with RSS-210 of Industry Canada. Operation is 
subject to the following two conditions: (1) This device may not cause harmful 
interference, and (2) This device must accept any interference received, including 
interference that may cause undesired operation. 

 

•   The Alertco RF / RFID wireless component must be installed by qualified 

professional or contractors in accordance with FCC part 15.023, Antenna Requirements. 

 

•  Do not use any antenna other than an approved antenna, such as the one provided with 

the unit. For a complete list of approved antennas, contact RF Wireless Solutions 

 

10  UL Compliance 

 

•  This device is tested to UL 294 standards with the Mercury Security access control 

system but is not exclusive to that system. 

 

•   This device is tested to UL 294 standards with the HID reader. 

 

11  Warnings 

 

RFWireless/cramZ marketing is in no way liable for incorrect installations of the RFID 
products which may cause damage to equipment or persons.  End users, installers, purchasers 
or anyone using, buying, selling or using this product must follow the exact installation 
instructions as outlined in the instruction manual.  Correctly installed equipment including 
approved enclosures and wiring must be used as outlined in the installation or user 
manual.  Failure to follow instructions outlined in this instruction manual will void the listed 
approvals and any warranty. 

 

Any changes or modifications not expressly approved by RFWireless/cramZ marketing 
will void the approvals by all governing bodies and void any product warranty. 

 

Installation must be carried out by a trained authorized access control installation technician 
to all local or municipal governmental electrical codes. 

 
 
 
 
 
 
 
 
 
 
 
 
 
 

15

Summary of Contents for 900-R





















Reviews:

No comments

Brands by name

Popular brands

Load more brands