7
English
1. Plug the charger plug into the charger port
4
.
2. Plug the charger into any standard 120 Volt 60 Hz
electrical outlet.
3. Your tool should be fully charged in 4-5 hours from
a fully discharged condition. Recharge discharged
batteries as soon as possible after use or battery life may
be greatly diminished. For longest battery life, do not
discharge batteries fully. It is recommended that the
batteries be recharged after each use or when the LED
work light fails to illuminate or the tools performance
is diminished. Green LED lights on the tool indicate the
state of charge when the tool is actuated.
nOTE:
The blue LED on the unit indicates the unit is
charging. When the LED turns off the unit is charged.
nOTE:
If your tool has been deeply discharged it may take
several minutes for the charger LED to illuminate after
connection to the tool.
Important Charging Notes
1. Longest life and best performance can be obtained if
the battery pack is charged when the air temperature
is between 65 °F – 75 °F (18 ° C– 24 °C). DO NOT charge
when the battery pack is below +40 °F (+4.5 °C), or
above +104 °F (+40 °C). This is important and will
prevent serious damage to the battery pack.
2. The charger and battery pack may become warm to the
touch while charging. This is a normal condition, and
does not indicate a problem.
3. If the battery pack does not charge properly:
a. Check operation of receptacle by plugging in a lamp
or other appliance;
b. Check to see if receptacle is connected to a light
switch which turns power off when you turn out
the lights;
c. Move the charger and battery pack to a location
where the surrounding air temperature is
approximately 65 °F – 75 °F (18 °C – 24 °C);
d. If charging problems persist, take the tool, battery
pack and charger to your local service center.
4. The battery pack should be recharged when it fails to
produce sufficient power on jobs which were easily
done previously. DO NOT CONTINUE to use under these
conditions. Follow the charging procedure. You may
also charge a partially used pack whenever you desire
with no adverse effect on the battery pack.
5. To maximize battery life:
a. Do not fully discharge batteries.
b. Fully recharge batteries after each use.
c. Store tool in a location where the surrounding air
temperature is approximately
40 °F – 75 °F (4.5 °C – 24 °C).
d. Disconnect charger from tool after charge
is complete.
WARNING:
Fire Hazard. When disconnecting the
charger from the tool, be sure to unplug the charger
from the outlet first, then disconnect the charger cord
from the tool.
Charger Cleaning Instructions
WARNING:
Shock hazard. Disconnect the charger
from the AC outlet before cleaning. Dirt and grease
may be removed from the exterior of the charger using
a cloth or soft non-metallic brush. Do not use water or
any cleaning solutions.
Fig. B
4
5
UBS Power Port (Fig. B)
The USB symbol
5
on the base of this tool indicates that
this tool is equiped with a USB charging port.
Intended Use
The gyroscopic screwdriver is designed for
fastening applications.
DO nOT
use under wet conditions or in presence of
flammable liquids or gases.
DO nOT
let children come into contact with the tool.
Supervision is required when inexperienced operators use
this tool.
Charging Procedure (Fig. B)
WARNING:
The batteries in your tool are not fully
charged at the factory. Before attempting to charge
them, thoroughly read all of the safety instructions.
WARNING:
Do not use tool while it is connected to
the charger.
WARNING:
Fire Hazard. When disconnecting the
charger from the tool, be sure to unplug the charger
from the outlet first, then disconnect the charger cord
from the tool.
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of serious personal
injury, turn unit off and lock off the tool before
making any adjustments or removing/installing
attachments or accessories.
An accidental start-up
can cause injury.
