English
8
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of serious personal
injury, turn unit off and disconnect it from
power source and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories.
An
accidental start-up can cause injury.
THIS PRODUCT USES THE BATTERY
AND CHARGER LISTED IN THE
CHART BELOW
Description
Catalog number
20V Max* Lithium-Ion Battery
CMCB201, CMCB2011,
CMCB202, CMCB204,
CMCB205
20V Max* Lithium-Ion Battery Charger
CMCB100, CMCB102,
CMCB104
SAVE THESE INSTRUCTIONS FOR
FUTURE USE
COMPONENTS (FIG. A)
Motor
Be sure your power supply agrees with the nameplate
marking. Voltage decrease of more than 10% will cause loss
of power and overheating. These tools are factory tested; if
this tool does not operate, check power supply.
Intended Use
This inflator is designed for household use.
DO nOT
use under wet conditions or in presence of
flammable liquids or gases.
DO nOT
let children come into contact with the tool.
Supervision is required when inexperienced operators use
this tool.
Wall Mounting
These chargers are designed to be wall mountable or to
sit upright on a table or work surface. If wall mounting,
locate the charger within reach of an electrical outlet,
and away from a corner or other obstructions which may
impede air flow. Use the back of the charger as a template
for the location of the mounting screws on the wall. Mount
the charger securely using drywall screws (purchased
separately) at least 1" (25.4 mm) long, with a screw head
diameter of 0.28–0.35" (7–9 mm), screwed into wood to an
optimal depth leaving approximately 7/32" (5.5 mm) of the
screw exposed. Align the slots on the back of the charger
with the exposed screws and fully engage them in the slots.
Versatrack
CRAFTSMAN chargers can be mounted to the wall using
CRAFTSMAN Versatrack Trackwall. Hooks and accessories
are sold separately. Please refer to the Versatrack Trackwall
accessory sheet for further information.
Storage (Fig. A)
12V AC Adapter storage
Wrap the 12V AC cord around the cord retainer located in
the side of the inflator and snap the 12V AC connector
14
into its storage location on the cord retainer.
120V AC Cord storage
Coil the 120V AC cord
13
into its storage location located
on the side of the inflator.
Air hose storage
The high-pressure hose
10
is located in a storage channel
around the face of the unit. Wrap the high-pressure hose
inside the channel.
high-Volume hose storage
The high-volume hose
7
is located in a storage channel
around the side of the unit. Wrap the high-volume hose
inside the channel.
Accessories storage
The accessories
15
,
16
, and
17
are stored in the back of
the unit inside the accessory storage area.
Fitting the Accessories
Universal Valve Adapter (Fig. B)
Your inflator is supplied with the inflator needle valve
15
,
a brass coupler
16
, and the standard tapered nozzle
17
,
located on the side of the unit.
1. To use the universal valve adapter
9
, make sure the
lever is in the up position.
2. Place the valve adapter over the stem of the inflator
needle valve, brass coupler adapter or standard
tapered nozzle.
3. Press the lever
18
on the universal valve adapter down
to lock it in place.
4. Place the inflator needle valve, brass coupler adapter or
tapered nozzle into the item to be inflated.
nOTE:
Always make sure that the lever is in the up position
when not in use. Operate your inflator only with the
universal valve adapter or with the included nozzles.
nOTE:
Make sure the universal valve adapter is firmly
locked in place before turning the inflator on.
Figure B
17
16
15
18
9
High-Volume Hose (Fig. C)
1. Remove the high-volume hose
7
from the
storage location.
2. Line up the notches
19
of the hose with the nubs
20
of the high volume pump inflator connection
12
.
Components
Tool
Use
inflator
household
