9
English
Belt Hook (Optional Accessory) (Fig. I)
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories.
WARNING: To reduce the risk of serious personal
injury, DO NOT
suspend tool overhead or suspend
objects from the belt hook.
ONLY
hang tool’s belt hook
from a work belt.
WARNING: To reduce the risk of serious personal
injury,
ensure the screw holding the belt hook
is secure.
WARNING: Do not carry the tool by the belt hook
with a bit in the collet.
iMPORTAnT:
When attaching or replacing the belt
hook
14
, use only the screw
15
that is provided. Be sure to
securely tighten the screw.
The belt hook can be be attached to either side of the tool
using only the screw provided, to accommodate left‑ or
right‑ handed users. If the hook is not desired at all, it can be
removed from the tool.
To move belt hook, remove the screw that holds it in place
then reassemble on the opposite side. Be sure to securely
tighten the screw.
Depth Guide (Fig. A)
Cutting depth guide
2
snaps onto locators as shown. Keep
depth guide in place at all times during operation of the tool.
For best results, adjust the guide using the knob to allow the
bit to protrude about 1/8” (3 mm) past the material to be cut.
Installing and Removing the Bit (Fig. A)
This tool is designed for spiral cutting bits with either a 1/8"
(3 mm), 5/32" (4 mm) (not included), or 1/4" (6 mm) shank
and has a tool‑free bit change system. To change bits, FIRST
turn off the tool and disconnect the battery from the tool.
Remove the cutting depth guide
2
.
1. To replace bit, depress both spindle lock button
6
and
collet lock
4
and turn collet grip
5
counterclockwise.
2. Insert or remove bit.
WARNING:
The bits are sharp and should be handled
with great care.
CAUTION:
When replacing bits, do not insert cutting
flutes into the collet. This may result in broken bits.
3. While depressing both spindle and collet locks, turn
the collet grip clockwise to firmly tighten the collet. For
some heavy duty applications, it may be necessary to
use a wrench to further tighten the collet nut
3
while
depressing the spindle lock button
6
.
4. Attach guide.
CAUTION:
Never tighten the collet without a
bit installed.
This tool comes with both 1/8” (3 mm) and 1/4” (6 mm)
collets. To change collets, remove the collet nut and insert
the desired collet.
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories.
An
accidental start‑up can cause injury.
Wall Mounting
Some CRAFTSMAN chargers are designed to be wall
mountable or to sit upright on a table or work surface. If wall
mounting, locate the charger within reach of an electrical
outlet, and away from a corner or other obstructions which
may impede air flow. Use the back of the charger as a
template for the location of the mounting screws on the wall.
Mount the charger securely using drywall screws (purchased
separately) at least 1” (25.4 mm) long, with a screw head
diameter of 0.28–0.35” (7–9 mm), screwed into wood to an
optimal depth leaving approximately 7/32” (5.5 mm) of the
screw exposed. Align the slots on the back of the charger
with the exposed screws and fully engage them in the slots.
nOTE:
Do not attempt to mount CMCB101 charger under a
bench or table.
nOTE:
Only mount CMCB101 charger with the charging
lights pointed upward toward the ceiling.
VersaTrack™
WARNING:
Do not charge batteries while charger is
hung on Trackwall.
CRAFTSMAN chargers, except the CMCB101, can
be stored on CRAFTSMAN VersaTrack™ Trackwall.
Hooks and accessories are sold separately. Please
refer to the VersaTrack™ Trackwall accessory sheet for
further information.
nOTE:
The CMCB101 charger is not CRAFTSMAN VersaTrack™
Trackwall compatible.
SAVE THESE INSTRUCTIONS FOR
FUTURE USE
a. Check operation of receptacle by plugging in a lamp
or other appliance;
b. Check to see if receptacle is connected to a light
switch which turns power off when you turn out
the lights;
c. If charging problems persist, take the tool, battery
pack and charger to your local service center.
4. You may charge a partially used pack whenever you
desire with no adverse effect on the battery pack.
Charger Cleaning Instructions
WARNING:
Shock hazard. Disconnect the charger
from the AC outlet before cleaning. Dirt and grease
may be removed from the exterior of the charger using
a cloth or soft non‑metallic brush. Do not use water or
any cleaning solutions.
