Craftsman CM2.12 Operation Manual Download

Page: 7 / 48

General maintenance directives 6

CM 2.12, CM 2.16 & CM 3.27

By carefully adhering to the following recommendations, you will be sure of the

best possible conditions to operate your engine, resulting in a long life span, excel-

lent performance and fuel economy.

• Have the maintenance procedures regularly executed, as mentioned in this

manual.

• Prior to starting the engine, always verify the correct level of the various fluids.

• All year long, use a good quality anti-freeze product, protecting your engine

against corrosion and frost damage. Please see page 43 for the specifications of

the cooling liquid.

• Do not ever put the engine into operation without a properly functioning thermo

stat, so as to avoid overheating of the engine.

• Always use the correct quality of lubricants, as specified on page 13 of this

manual.

• Always use good quality diesel fuel, free from water and /or other impurities.

• Switch-off the engine immediately if the monitoring light(s) of oil pressure, fresh

water temperature, raw water temperature and/or battery charging control light

up.

craftsman marine diesel engines CM2.12 , cm2.16 / cm3.27

Summary of Contents for CM2.12

















































Search results

Summary of Contents for CM2.12

Reviews:

Related manuals for CM2.12

Brands by name

Popular brands

Craftsman CM2.12, Operation Manual

Search results

Summary of Contents for CM2.12

Reviews:

Related manuals for CM2.12

Brands by name

Popular brands