background image

12  Winter storage

Protective fuel mixture

So as to protect your engine well during the standstill 

of the winter season, it is recommended to have the 

engine running for some 10 minutes with a protective 

mixture of 10% lubrication oil and 90% of clean diesel 

fuel.

 

With  this  mixture:  idling  revolutions 

only, no revving up allowed! 

Lubrication oil system

Replace the oil filter and change the engine lubrication 

oil with a good quality of oil, with protective proper-

ties. See page 26.

Raw water cooling system

Close the raw water seacock and clean the raw water 

strainer.  Drain  so  much  cooling  liquid  from  the  inner 

cooling  circuit,  so  as  to  enable  you  to  add  1  liter  of 

(extra)  anti-freeze  into  the  cooling  circuit.  Have  the 

motor idling for a few seconds, so that the additional 

anti-freeze can be spread throughout the system. 

Anti-freeze  liquid  is  very  poisonous  ! 

Make  sure  anti-freeze  is  not  getting 

mixed up with raw water 

When  closing  the  cover  of  the  raw  water  strainer, 

make sure that it tightens well. If false air is coming 

into  the  system  through  a  cover  that  is  not  closed 

tightly,  there  is  a  severe  risk  of  overheating  of  the 

engine.

32

craftsman marine diesel engines CM2.12 , cm2.16 / cm3.27

Summary of Contents for CM2.12

















































Reviews: