manualshive.com logo in svg

Craftsman 944.365220, Owner'S Manual, Page: 15 / 20

Share
Download
Craftsman 944.365220 Owner'S Manual Download Page 15

15

KEY    PART
NO.     NO.              DESCRIPTION

- -       

590737

       Rewind Starter, Complete

3         590740        Retainer
6         590616        Starter Dog
7         590617        Dog Spring
8         590618A     Pulley & Rewind Spring Assembly
11       590687B     Starter Housing Assembly
                              (40 Degree Grommet)
12       590535        Starter Rope (98" x 9/64" diameter)
13       590701        Starter Handle
14       590760        Spring Clip

KEY    PART
NO.     NO.              DESCRIPTION

- -       

590694

       Recoil Starter Assembly, Complete

1         590599A     Spring Pin (Includes Key Number 4)
2         590600        Washer
3         590696        Retainer
4         590601        Washer
5         590697        Brake Spring
6         590698        Starter Dog
7         590699        Dog Spring
8         590700        Pulley & Rewind Spring Assembly
11       590695A     Starter Housing Assembly
                              (40 Degree Grommet)
12       590535        Starter Rope (98" x 9/64" diameter)
13       590701        Starter Handle

KEY    PART
NO.     NO.              DESCRIPTION

- -        640339        Carburetor (Includes Key Number
                              184 of Engine Parts List)
1         631615        Throttle Shaft and Lever Assembly
2         631767        Throttle Return Spring
4         631184     *  Dust Seal Washer
5         631183     *  Dust Seal, Throttle
6         640070        Throttle Shutter
7         650506     *  Shutter Screw
16       631807        Fuel Fitting
17       651025        Throttle Crack / Idle Speed Screw
18       630766        Tension Spring
20       640016        Idle Restrictor Screw
20A     640200        Idle Restrictor Cap Screw (Black)
25       631867        Float Bowl
27       631024     *  Float Shaft
28       632802        Float (Plastic)
29       631028     *  Float Bowl “O” Ring
30       631021A  *  Inlet Needle, Seat and Clip
                              (Includes Key Number 31)
31       631022        Spring Clip
35       640259        Primer Bulb / Retainer Ring
36       640080        Main Nozzle Tube
36A     632766        Carburetor Tube 
37       632547     *  “O” Ring, Main Nozzle Tube
40       640030        High Speed Bowl Nut
44       27110A    *  Bowl Nut Washer
47       630748     *  Welch Plug, Idle Mixture Well
48       631027     *  Welch Plug, Atmospheric Vent
60       632760B     Repair Kit
                              (Includes All Items Marked * )

NOTE:

All component dimensions given in U.S. inches

             1 inch = 25.4 mm

MODEL NUMBER LV148EA-334005

TECUMSEH 4-CYCLE ENGINE

590694

590737

Summary of Contents for 944.365220





















Reviews:

No comments