manualshive.com logo in svg

Craftsman 944.365220, Owner'S Manual, Page: 12 / 20

Share
Download
Craftsman 944.365220 Owner'S Manual Download Page 12

12

Lower 
handle

ROTATE

ENGINE

ENGINE SPEED

Your engine speed has been factory set. 
Do not attempt to increase engine speed 
or it may result in personal injury. If you 
believe that the engine is running too fast 
or too slow, take your lawn mower to a 
Sears or other qualifi ed service center for 
repair and adjustment.

CARBURETOR

Your carburetor has a non-adjustable fi xed 
main jet for mixture control.  If your engine 
does not operate properly due to sus pect ed 
carburetor problems, take your lawn mower 
to a Sears or other qualifi ed service center 
for repair and/or ad just ment.

IMPORTANT:

  Never tamper with the 

engine governor, which is factory set 
for proper engine speed.  Over speed ing 
the engine above the factory high speed 
setting can be dangerous.  If you think 
the engine-governed high speed needs 
adjusting, contact a Sears or other 
qualifi ed service center, which has proper 
equip ment and ex pe ri ence to make any 
nec es sary adjustments.

STORAGE

Immediately prepare your lawn mower for 
storage at the end of the season or if the 
unit will not be used for 30 days or more.

LAWN MOWER

When lawn mower is to be stored for a 
period of time, clean it thor oughly, remove 
all dirt, grease, leaves, etc.  Store in a 
clean, dry area.
1.   Clean entire lawn mower (See 

“CLEANING” in the Maintenance sec-
tion of this manual).

2.   Lubricate as shown in the Main te nance 

section of this manual.

3.   Be sure that all nuts, bolts, screws, and 

pins are securely fas tened.  Inspect   
moving parts for damage, breakage 
and wear.  Replace if necessary.

4.   Touch up all rusted or chipped paint 

surfaces; sand lightly before painting.

HANDLE

You can fold your mower handle for storage.
1.   Squeeze the bottom ends of the lower 

handle toward each other until the 
lower handle clears the handle bracket, 
then move handle forward.

2.   Loosen upper handle mounting bolts 

enough to allow upper handle to be 
folded back.

IMPORTANT:

  When folding the handle for 

storage or transportation, be sure to fold 

Lower handle

SQUEEZE

TO FOLD

Mowing 
position

Mowing 
position

HIGH POSITION

LOW POSITION

Handle 
bracket

Hairpin 
cotter
Mounting 
pin

FOLD
FORWARD
FOR
STORAGE

MOWING 

POSITION

Lower handle

Operator 
presence 
control bar

Upper 

handle

Handle 

knob

the handle as shown or you may damage 
the control cables.
•  When setting up your handle from the 

storage position, the lower han dle will au-
tomatically lock into the mow ing position. 

Summary of Contents for 944.365220





















Reviews:

No comments