3
RULES FOR SAFE OPERATION
cord length and nameplate amperage rating. If in doubt, use the
next heavier size line gauge. The smaller the gauge number, the
heavier the cord. To prevent the cord from disconnecting from
the unit, use the cord hook shown in the
Operating Instructions
.
• A nameplate on your unit indicates the voltage used. Never
connect the unit to an AC voltage that differs from this voltage.
• Inspect all extension cords and the unit power connection
periodically. Look closely for deterioration, cuts or cracks in the
insulation. Also inspect the connections for damage. Repair or
replace the cords if any defects appear.
• Ground Fault Circuit Interrupter (GFCI) protection should be
provided on the circuit(s) or outlet(s) that will be used for the
unit. Use receptacles with built-in GFCI protection for an
extra measure of safety.
OTHER SAFETY WARNINGS
• Inspect the unit before use. Replace damaged parts. Make
sure all fasteners are in place and secure. Replace cutting
attachment parts that are cracked, chipped or damaged in
any way. Make sure the cutting attachment is properly
installed and securely fastened. Be sure that the cutting
attachment shield is properly attached, and positioned as
recommended. Failure to do so can result in personal injury to
the operator and bystanders, as well as damage to the unit.
• This unit was not designed to be used as a brushcutter. Do not
attach or operate this unit with any type of brushcutting blade or
brushcutting attachment. The use of any other accessory or
attachment may increase the risk of injury when used with this unit.
• Use only yellow Hassle Free IV™ XTRA QUIET Spiral Line.
Never use metal-reinforced line, wire, chain or rope. These can
break off and become dangerous projectiles.
• Be aware of risk of injury to the head, hands and feet.
• Be sure to secure the unit while transporting.
• Never douse or squirt the unit with water or any other liquid.
Keep handles dry, clean and free from debris. Clean after each
use. See the
Cleaning and Storage
instructions.
• Keep these instructions. Refer to them often and use them to
instruct other users. If you loan someone this unit, also loan
them these instructions.
WHILE OPERATING
• The cutting attachment shield must always be in place while
operating the unit. Do not operate unit without both trimming
lines extended, and the proper line installed. Do not extend the
trimming line beyond the length of the shield.
• Adjust the D-handle to your size to provide the best grip.
• Be sure the cutting attachment is not in contact with anything
before starting the unit.
• Use the unit only in daylight or good artificial light.
• Avoid accidental starting. Do not carry around a unit that is
plugged in with your finger on the trigger switch. Be sure the
switch is in the off position when plugging in the unit.
• Do not overreach. Always keep proper footing and balance.
• Always hold the unit with both hands when operating. Keep a
firm grip on both handles or grips.
• Keep hands, face, and feet at a distance from all moving parts. Do
not touch or try to stop the cutting attachment when it rotates.
• Always stop the motor when cutting is delayed or when
walking from one cutting location to another.
• If you strike or become entangled with a foreign object, stop
the motor immediately and check for damage. Do not
operate before repairing damage. Do not operate the unit
with loose or damaged parts.
• Stop the unit and unplug it for maintenance or repair.
• Keep unit clean of vegetation and other materials. They may
become lodged between the cutting attachment and shield.
• Do not force appliance-It will do the job better and with less
likelihood of a risk of injury at the rate for which if was designed.
SAVE THESE INSTRUCTIONS
This operator's manual describes safety and international symbols and pictographs that may appear on this product. Read the
operator's manual for complete safety, assembly, operating and maintenance and repair information.
• WARNING - READ OPERATOR'S MANUAL
Read the operator’s manual(s) and follow all warnings
and safety instructions. Failure to do so can result in
serious injury to the operator and/or bystanders.
SYMBOL
MEANING
• SAFETY ALERT SYMBOL
Indicates danger, warning or caution. May be used
in conjunction with other symbols or pictographs.
• WEAR EYE AND HEARING PROTECTION
WARNING:
Thrown objects and loud noise can
cause severe eye injury and hearing loss. Wear
eye protection meeting ANSI Z87.1 standards
and ear protection when operating this unit. Use
a full face shield when needed.
• KEEP BYSTANDERS AWAY
WARNING:
Keep all bystanders, especially
children and pets, at least 50 feet (15 m) from
the operating area.
• THROWN OBJECTS AND ROTATING
CUTTER CAN CAUSE SEVERE INJURY
WARNING:
Do not operate without the cutting
attachment shield in place. Keep away from the
rotating cutting attachment.
• SAFETY & INTERNATIONAL SYMBOLS •
• THROTTLE CONTROL
Indicates “HIGH” or “FASTEST” speed.
SYMBOL
MEANING
• THROTTLE CONTROL
Indicates “IDLE,” “LOW,” or “SLOWEST” speed.
• DOUBLE INSULATED
Two systems of insulation are provided in stead of
grounding. There is no grounding provided and no
means of grounding should be added to this unit.
• BLOWERS
WARNING:
Stop the motor and allow the
impeller to stop and unplug before cleaning or
performing any maintenance.
• SHARP BLADE
WARNING:
Sharp blade on cutting attachment
shield. To prevent serious injury, do not touch
the line cutting blade.
