background image

3

SAFETY INSTRUCTIONS

TRAINING

• 

Read, understand, and follow all instructions on the machine and in the 
manual(s) before attempting to assemble and operate. Keep this manual in 
a safe place for future and regular reference and for ordering replacement 
parts. 

• 

Read the Operator’s Manual and follow all warnings and safety instructions. 
Failure to do so can result in serious injury to the operator and/or bystanders. 

• 

Be familiar with all controls and their proper operation. Know how to stop 
the machine and disengage them quickly.

• 

Never allow children under 16 years of age to operate this machine. Children 
16 and over should read and understand the instructions and safe operation 
practices in this manual and on the machine and be trained and supervised 
by an adult.

• 

Never allow adults to operate this machine without proper instruction.

• 

Keep bystanders, pets, and children at least 75 feet from the machine while 
it is in operation. Stop machine if anyone enters the area.

• 

Never run an engine indoors or in a poorly ventilated area. Engine exhaust 
contains carbon monoxide, an odorless and deadly gas.

• 

Do not put hands and feet near rotating parts or in the feeding chambers 
and discharge opening. Contact with the rotating impeller can amputate 
fingers, hands, and feet.

• 

Never attempt to unclog either the feed intake or discharge opening, remove 
or empty bag, or inspect and repair the machine while the engine is running. 
Shut the engine off and wait until all moving parts have come to a complete 
stop. Disconnect the spark plug wire and ground it against the engine.

PREPARATION

• 

Thoroughly inspect the area where the equipment is to be used. Remove 
all rocks, bottles, cans, or other foreign objects which could be picked up or 
thrown and cause personal injury or damage to the machine. 

• 

Always wear safety glasses or safety goggles during operation and while 
performing an adjustment or repair, to protect your eyes. Thrown objects 
which ricochet can cause serious injury to the eyes.

• 

Wear sturdy, rough-soled work shoes and close-fitting slacks and shirts. 
Loose fitting clothes or jewelry can be caught in movable parts. Never 
operate this machine in bare feet or sandals. Wear leather work gloves when 
feeding material in the chipper chute.

• 

Before starting, check all bolts and screws for proper tightness to be sure the 
machine is in safe working condition. Also, visually inspect machine for any 
damage at frequent intervals.

• 

Maintain or replace safety and instructions labels, as necessary.

Safe Handling of Gasoline:

To avoid personal injury or property damage use extreme care in handling 
gasoline. Gasoline is extremely flammable and the vapors are explosive. 
Serious personal injury can occur when gasoline is spilled on yourself or your 
clothes which can ignite.  Wash your skin and change clothes immediately.

• 

Use only an approved gasoline container.

• 

Never fill containers inside a vehicle or on a truck or trailer bed with a plastic 
liner. Always place containers on the ground away from your vehicle before 
filling.

• 

When practical, remove gas-powered equipment from the truck or 
trailer and refuel it on the ground. If this is not possible, then refuel such 
equipment on a trailer with a portable container, rather than from a gasoline 
dispenser nozzle.

• 

Keep the nozzle in contact with the rim of the fuel tank or container opening 
at all times until fueling is complete. Do not use a nozzle lock-open device.

• 

Extinguish all cigarettes, cigars, pipes and other sources of ignition.

• 

Never fuel machine indoors.

• 

Never remove gas cap or add fuel while the engine is hot or running. Allow 
engine to cool at least two minutes before refueling.

• 

Never over fill fuel tank. Fill tank to no more than ½ inch below bottom of 
filler neck to allow space for fuel expansion.

• 

Replace gasoline cap and tighten securely.

• 

If gasoline is spilled, wipe it off the engine and equipment. Move unit to 
another area. Wait 5 minutes before starting the engine. 

 WARNING

This symbol points out important safety instructions which, if not 
followed, could endanger the personal safety and/or property of 
yourself and others. Read and follow all instructions in this manual 
before attempting to operate this machine. Failure to comply with these 
instructions may result in personal injury. When you see this symbol, HEED 
ITS WARNING!

 WARNING

CALIFORNIA PROPOSITION 65

Engine Exhaust, some of its constituents, and certain vehicle components 
contain or emit chemicals known to State of California to cause cancer and 
birth defects or other reproductive harm.

 DANGER

This machine was built to be operated according to the safe operation 
practices in this manual. As with any type of power equipment, 
carelessness or error on the part of the operator can result in serious injury. 
This machine is capable of amputating fingers, hands, toes and feet and 
throwing debris. Failure to observe the following safety instructions could 
result in serious injury or death.

 WARNING

Your Responsibility

—Restrict the use of this power machine to 

persons who read, understand and follow the warnings and instructions in 
this manual and on the machine. 

SAVE THESE INSTRUCTIONS!

Summary of Contents for 247.776150









































Reviews: